®
For model:
AV-24F702
COLOR TELEVISION
USER'S GUIDE
TV CATVVCR DVD
POWER
STANDARD
INPUT
1
2
5
8
0
3
6
BBE
4
DISPLAY
7
9
RETURN
SLEEP TIMER
C.C.
AUDIO SELECT LIGHT
RM-C309G
MUTING
ENTER
CH
VOL
VOL
CH
MENU
EXIT
+
–
VCR CHANNEL
PREV NEXT
VCR/DVD
POWER
TV/VCR
REW
REC
PLAY
FF
POWER
STOP
PAUSE
OPEN/CLOSE
STILL/PAUSE
TV
IMPORTANT NOTE TO THE CUSTOMER:
In the space below, enter the serial number for your
television (located on the rear of the television cabinet).
Staple your sales receipt or invoice to the inside cover of this guide.
Keep this user's guide in a convenient place for future reference.
Keep the carton and original packaging for future use.
Serial Number
13. LIGHTNING
To protect your unit during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the
wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line
surges.
14. POWER LINES
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits,
or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken
to keep from touching such power lines or circuits, as contact with them might be fatal.
15. OVERLOADING
Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out parts that could
result in fire or electric shock. Never spill or spray any type of liquid into the unit.
17. OUTDOOR ANTENNA GROUNDING
If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded to provide
some protection against voltage surges and built-up static charges, Section 810 of the National Electrical Code, ANSI/NFPA
70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding elec-
trodes, and requirements for the grounding electrode.
18. SERVICING
Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
19. DAMAGE REQUIRING SERVICE
Unplug this unit from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the unit.
c . If the unit has been exposed to rain or water.
d. If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by
the operating instructions, as an improper adjustment of other controls may result in damage and will often require
extensive work by a qualified technician to restore the unit to its normal operation.
e. If the unit has been dropped or the cabinet has been damaged.
f . When the unit exhibits a distinct change in performance, this indicates a need for service.
20. REPLACEMENT PARTS
When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or
those that have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other hazards.
21. SAFETY CHECK
Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the
unit is in proper operating condition.
22. HEAT
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
23. NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building,
as close to the point of cable entry as practical.
EXAMPLE OF ANTENNA GROUNDING AS PER THE NATIONAL ELECTRICAL CODE
ANTENNA LEAD IN WIRE
GROUND CLAMP
ANTENNA DISCHARGE UNIT (NEC
SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS (NEC SECTION
810-21)
GROUND CLAMPS
NEC-NATIONAL ELECTRICAL CODE
S2898A
POWER SERVICE GROUNDING ELECTRODE
SYSTEM (NEC ART 250, PART H)
3
FEATURES
• Flat Picture Tube - It reduces the influence of surrounding light resulting in outstanding image detail and clarity.
• 181 Channel Tuner - The tuning system is capable of receiving all 68 VHF/UHF standard broadcast channels that are available in
your area. When operating on a cable system, it can tune to the standard VHF channel frequencies plus up to 113 cable channel
frequencies. The actual number of channels received depends upon channel reception in your area or your cable system.
• On-Screen 3 Language Display - Consists of channel, sleep timer, volume level, muting, text/caption indicators and picture
control adjustments. These can be displayed in English, Spanish or French.
• ON/OFF Timer - Allows you to automatically turn on or off your TV at a set time.
• Sleep Timer - Operable from the remote control, this TV can be programmed up to 120 minutes to turn off automatically.
• V-Chip - The V-Chip function can read the rating of a TV program or movie content if the program is encoded with this
information. The V-Chip will allow you to set a restriction level (US only).
• Picture Control Adjustments - The On-Screen display allows precise remote control adjustment of BRIGHTNESS, COLOR,
CONTRAST, SHARPNESS, TINT and COMPONENT.
• Closed Captioned Decoder - Displays text captions or 1/2 of full screen text on the screen for hearing impaired viewers.
• Stereo/SAP Reception - This TV is designed to receive stereo and separate audio program (SAP) broadcasts where available.
• BBE- BBE gives you the vivid sound with so much presence.
• Video Input Jacks - This unit is equipped 3 types of video input jacks. The component video in jacks and S-video in jack enable
you to watch the DVD player or the video devices with high quality picture.
• Remote Control - You can operate your VCR, Cable Box, Satellite Dish and DVD after you have registered the 3-digit codes for
their brand name.
LOCATION OF CONTROLS
FRONT
BACK
IN
OUT
VIDEO
Y
ANT(75Ω)
VIDEO
P
B
L/MONO
L/MONO
AUDIO
AUDIO
S-VIDEO
PR
R
R
POWER
VIDEO
1
VIDEO
2
8
9
10 11
12
HOW TO OPEN THE FRONT DOOR
POWER
VIDEO
3
IN
VIDEO
L/MONO
AUDIO
R
ON TIMER
CHANNEL
VOLUME
1 2 3
4
5
6
7
1. POWER Button - Press to turn the TV on or off.
2. Remote Sensor - Signals from the Remote Control unit
are received here.
3. ON TIMER Indicator - This indicator lights up when the
powered up. It also lights up when ON TIMER program
is turned ON while power is OFF.
4. CHANNEL +/– Buttons - Press to select a higher or
lower numbered channel set into memory.
5. VOLUME +/– Buttons - Press to raise or lower the
volume of the sound.
9. VIDEO 1 IN Jacks (Rear) - Audio and video signal
cables from an external source (ex. VCR) can be
connected here. If your video device has S-video out
jack, connect to S-video in jack.
10. VIDEO 2 IN Jacks - Audio and video signal cables from
an external source (ex. DVD) can be connected here.
If you have a DVD with component video out jacks,
connect to the component video in jacks. If you have a
video device without the component video out, connect
to video in jack.
6. VIDEO 3 IN Jacks (Front) - Audio and video signal
cables from an external source can be connected here.
7. HEADPHONES JACK - Plug an earphone or headphones
with an 1/8 miniplug into this jack for listening.
11. REAR AUDIO (L / R) /VIDEO OUT Jacks - Used to
output audio and video signals to a TV, amplifier or VCR.
NOTE: This video out jack does not output the signal
from component video in jacks.
8. VHF/UHF IN (ANT) Jack - Connect a VHF/UHF antenna 12. AC Power Cord - Connect to a 120V, 60Hz outlet.
or CATV cable to this jack.
4
REMOTE CONTROL
VCR
DVD
TV CATV
11
12
POWER
1
STANDARD
INPUT
2
3
13
14
1
4
7
2
5
3
6
BBE
4
5
DISPLAY
8
0
9
RETURN
SLEEP TIMER
15
16
C.C. AUDIO SELECT LIGHT
6
7
RM-C309G
MUTING
ENTER
17
18
+
CH
VOL
+
VOL
8
CH
19
20
MENU
EXIT
9
VCR CHANNEL
PREV NEXT
VCR /DVD
POWER TV/VCR
10
REW
PLAY
FF
STOP PAUSE
STILL/PAUSE
REC
OPEN/CLOSE
TV
1. TV/CATV Switch - Used to select the TV or Cable Box
to be operated. (You can operate your cable box after
you have programed the remote control.)
2. VCR/DVD switch - Used to select the VCR or DVD to
be operated. (You can operate your VCR or DVD after
you have programed the remote control.)
10. VCR or DVD Operation Buttons - Press to operate
your VCR or DVD.
11. POWER Button - Press to turn the TV on or off.
12. STANDARD Button - Press to reset the On-Screen
picture adjustments or Audio adjustment to their factory
preset positions.
3. BBE Button - Press to turn BBE On or Off.
4. DISPLAY Button - Displays the current status time,
channel (or Input), the present settings on the TV screen.
5. SLEEP TIMER Button - Sets the TV to turn off auto-
matically after up to 120 minutes.
6. C.C. (Closed Caption) Button - Switches between
Caption, Text and TV modes for Closed-Captioned
programs.
13. INPUT Button - Switches between the TV and external
input sources.
14. 10-key pad - Allows direct access to any channel of the
TV, VCR or Cable box.
15. RETURN Button - Switches between the present
channel and the last channel selected.
16. LIGHT Button - Press to turn the illumination on for CH
+/– and VOL +/– buttons.
17. AUDIO SELECT Button - Switches sound between
mono and stereo, and SAP when receiving broadcasts
in stereo or SAP.
18. ENTER Button - Press to enter selected setup.
19. VOL +/– Buttons - Press the + button to increase, or
the – button to decrease the volume level. Press to
select the desired setting or arrangement during On-
Screen operations.
7. MUTING Button - Press to turn off the sound. Press
again to turn the sound back on.
8. CH +/– Buttons - Press the + button to change to a
higher numbered channel set into memory. Press the –
button to change to a lower numbered channel set into
memory. Press to select the desired item during On-
Screen operations.
9. MENU Button - Press to display the On-Screen menu
function.
20. EXIT Button - Press to exit the On-Screen menu
function.
5
REMOTE CONTROL
(CONTINUED)
BATTERY INSTALLATION
BATTERY PRECAUTIONS
1. Slide the battery compartment cover in the direction
The precautions below should be followed when using
batteries in this device:
of the arrow.
1.Use only the size and type of batteries specified.
2.Be sure to follow the correct polarity when installing the
batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
To avoid a potential short circuit, insert the “–” end first.
3.Do not mix different types of batteries together (e.g.
Alkaline and Carbon-zinc) or old batteries with fresh
ones.
2. Install two “AA” (penlight size) batteries, paying
attention to the polarity diagram in the battery
compartment.
4.If the device is not to be used for a long period of time,
remove the batteries to prevent damage or injury from
possible battery leakage.
5.Do not try to recharge batteries not intended to be
recharged; they can overheat and rupture. (Follow
battery manufacturer’s directions.)
6.When you change the batteries, try to complete the task
within three minutes. If you take longer than three
minutes, the remote control codes for your Cable Box
may have to be reset (see page 8).
3. Replace the compartment cover.
EFFECTIVE DISTANCE OF THE REMOTE CONTROL TRANSMITTER
15 FEET
30˚
30˚
NOTES: • When there is an obstacle between the TV and the transmitter, the transmitter may not operate.
• When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong light shines on the
Remote sensor of the TV, the remote operation may be unstable.
6
REMOTE CONTROL BASICS
• Before you can operate the remote control, you must first install
the batteries (included). See “Changing the Batteries” on this
page above for instructions. (For an illustration, please see page 6.)
• Press the POWER button to turn the television on or off.
• Make sure the TV/CATV switch is set to TV. Move the switch to
CATV only if you need to operate a cable box.
VCR
TV CATV
DVD
POWER
• Slide the VCR/DVD selector switch to VCR to control a VCR,
slide to DVD to control a DVD player. Please see pages 8 to 10
for instructions on programming your remote control to operate a
Cable box, VCR or DVD player.
• Press the CH + and CH – buttons to scan through the channels.
Tap the CH + or CH – button to move through the channels one
channel at a time.
• Press VOL + or VOL – to raise or lower the volume. An indicator
bar will appear onscreen to show you the television volume level.
• The CH +/– and VOL +/– buttons are also used to navigate JVC’s
onscreen menu system.
• You can directly access specific channels using the 10-key pad.
• This remote includes illuminated buttons for key features like CH
+/– buttons, and VOL +/– buttons. Press the LIGHT button to turn
the illumination on.
STANDARD
INPUT
1
4
7
2
5
3
6
BBE
DISPLAY
8
0
9
RETURN
SLEEP TIMER
C.C. AUDIO SELECT
LIGHT
CHANGING THE BATTERIES
RM-C309G
Push down on the remote’s back cover and slide towards the
bottom to remove it.
MUTING
ENTER
+
CH
Insert two AA batteries (supplied), carefully noting the “+” and “–”
markings on the batteries and on the remote control. To avoid a
potential short circuit, insert the “–” end first.
VOL
VOL
+
Be sure to use only size AA batteries.
When batteries are installed, slide the cover back into place (until it
clicks into position).
CH
• If the remote control acts erratically, replace the batteries. Typical
battery life is six months to one year. We recommend using
alkaline batteries for longer battery life.
When you change the batteries, try to complete the task within
three minutes. If you take longer than three minutes, the remote
control codes for your VCR, DVD, and/or Cable Box may have to
be reset (pages 8-10).
MENU
EXIT
VCR /DVD
POWER
VCR CHANNEL
PREV NEXT
TV/VCR
FF
REW
PLAY
STOP
PAUSE
REC
OPEN/CLOSE
STILL/PAUSE
TV
7
REMOTE CONTROL
(CONTINUED)
REMOTE PROGRAMMING
Setting the CATV, VCR and DVD Codes
You can program your remote to operate your cable box, satellite receiver, VCR or DVD player by using the
instructions and codes listed below. If the equipment does not respond to any of the codes listed below or to the
code search function, use the remote control supplied by the manufacturer.
Cable Box or Satellite setup
The remote control is programmed with CATV and/or Satellite codes for power on, power off, channel up, channel
down, and 10 key operation.
1) Find the CATV/Satellite brand from the list of codes shown below.
2) Slide the 2-way selector switch to “CATV ”.
3) Press and hold down the DISPLAY button.
4) With the DISPLAY button held down, enter the first code number listed using the 10 key pad.
5) Release the DISPLAY button.
6) Confirm the operation of the Cable Box/Satellite receiver.
• If your CATV or Satellite box does not respond to the first code, try the others listed. If it does not respond to any
code, try the Search Codes Function as shown below.
Cable Box
CODES
Cable Box
CODES
ABC
024
Pulsar
051, 032
Archer
032, 025
051, 032
022, 051
058, 059
024, 032, 025
029
034
032, 051
022, 043
Puser
RCA
Realistic
Regal
Regency
Rembrandt
Samsung
Scientific Atlanta
SLMark
032
061, 070
032
058, 064, 040, 041, 042, 045, 068
034
037, 032, 051, 038
051
057, 058, 059
051, 047
051, 056
032, 051
067
047, 051
044
035, 036, 066
050
032, 025
022, 032
052
029, 030
063, 046
Cableview
Citizen
Curtis
Diamond
Eagle
Eastern
GC Brand
Gemini
General Instrument 065, 024, 025, 026, 027, 020, 021, 022, 057, 023 Sprucer
Hamlin
Hitachi
Jerrold
Macom
Magnavox
Memorex
Movietime
Oak
Panasonic
Paragon
Philips
040, 041, 042, 045, 058, 064
049, 024
065, 024, 025, 026, 027, 020,021, 022, 057, 023
049, 050, 051, 054
033
030
032, 051
039, 037, 048
055, 056, 060, 071
063
028, 029, 030, 052, 053, 031, 069
047, 062
Stargate
Telecaption
Teleview
Texscan
Tocom
Toshiba
Unika
Universal
Videoway
Viewstar
Zenith
Pioneer
Zenith/Drake Satellite 046
Digital Satellite
Systems
Echostar
Express VU
G.E.
G.I.
Gradiente
Hitachi
Digital Satellite
CODES
CODES
Systems
Philips
100, 113, 114
100, 113
106
108
112
104, 111
104
105
102, 103
108
106, 109, 110
106, 109, 110
107
104, 108
101
102, 103
Primestar
Proscan
RCA
Sony
Star Choice
Toshiba
Uniden
HNS (Hughes)
Pranasonic
Cable/Satellite Search Codes Function:
1) Slide the 2-Way Mode Selector switch to CATV.
2) Press the TV POWER and RETURN buttons. Hold for at least three seconds and release.
3) Press TV POWER, see if the CATV or Satellite box responds.
4) If there was a response, press RETURN. The operating codes are now set. If there was no response, repeat Step 3.
If you repeat Step 3 a total of 52 times without a response, use the remote control which came with the equipment.
5) Press RETURN to exit.
8
VCR setup
The remote control is programmed with VCR codes for power on, power off, play, stop, fast-forward, rewind, pause,
record, channel up, and channel down operation.
1) Find the VCR brand from the list of codes shown below.
2) Slide the first 2-way selector switch to “TV ”and the other 2-way selector switch to “VCR ”.
3) Press and hold down the DISPLAY button.
4) With the DISPLAY button held down, enter the first code number listed with the 10 key pad.
5) Release the DISPLAY button.
6) Confirm the operation of the VCR.
• If your VCR does not respond to the first code, try the others listed. If it does not respond to any code, try the
Search Codes Function as shown below.
• Some manufacturer’s VCR’s may not respond to the TV/VCR button, even if other buttons work properly.
• To record, hold down the REC button on the remote and press PLAY.
VCRs
CODES
VCRs
CODES
Admiral
Aiwa
035
027, 032, 095
Optimus
Orion
028, 021, 035, 064
026, 020
Akai
029, 072, 073, 074
003, 005
063, 071
020, 026, 094
023, 025
043
064
063, 029, 064
Panasonic
Penney
Pentax
Philco
Philips
Pioneer
Proscan
Quasar
Radio Shack
RCA
Realistic
Samsung
Samtron
Sansui
Sanyo
Scott
Sears
Shintom
Sharp
Signature 2000
Singer
Sony
SV 2000
Sylvania
Symphonic
Tashiro
Tatung
023, 024, 021, 022
024, 058, 045, 063, 003, 004, 005, 093
058, 005, 045, 093
031, 024, 027, 023, 026, 020, 043
031, 023, 024, 086
023
045, 058, 023, 024, 031, 046, 059, 060, 033, 087, 093
021, 022, 023, 024
033, 024, 063, 036, 067, 040, 027
033,045,058,023,024,031,046,059,060,083,084,085,087,093
024, 063, 036, 067, 040, 027
037, 060, 062,033, 089
089
003, 026, 020, 052
063, 067, 091, 071
059, 060, 062, 067, 038, 040, 047, 048, 026, 020
063, 064, 065, 066, 058, 000, 001
075
035, 036, 080,088
027, 035
075
028, 029, 030, 053, 054, 055
027
031, 023, 024, 027
027, 081
064
003, 004, 005
003, 004, 027, 005
021, 022, 023, 024
024, 027, 070
059, 046, 079
005
Audio Dynamic
Bell & Howell
Broksonic
Canon
CCE
Citizen
Craig
Curtis Mathes
Daewoo
DBX
Dimensia
Emerson
Fisher
045, 024, 027, 093
043, 059, 024, 092
003, 004, 005
045, 093
043, 026, 077, 061, 025, 042, 020, 076
063, 066, 067, 065, 071, 091
027, 026, 020, 000
033, 045, 024
037, 051, 049, 050, 089
064
083, 084, 081, 000, 001
023, 045, 058, 027, 081, 093
024, 023
Funai
G.E.
Go Video
Goldstar
Gradiente
Hitachi
Instant Replay
Jensen
JVC
Kenwood
LXI
Magnavox
Marantz
Marta
Memorex
MGA
Minolta
Mitsubishi
Multitech
NEC
003
000, 001, 002, 003, 004, 005
003, 004, 064, 005
027, 064, 058, 065, 066, 063, 067
031, 023, 024, 086
003, 004, 005
064
024, 067
Teac
Technics
Teknika
Toshiba
Vector Research
Wards
038, 040, 047, 048, 041, 042
058, 045, 093
038, 040, 047, 048, 041, 042, 078, 090
047, 027, 062
003, 004, 005, 000
024, 023
035, 036, 067, 044, 064
063, 003, 004, 005
044, 082, 064, 094
Yamaha
Zenith
Olympic
VCR Search Codes Function:
1) Slide the first 2-way selector switch to “TV ” and the other 2-way selector switch to “VCR ”.
2) Press the VCR POWER and RETURN buttons. Hold for at least three seconds and release.
3) Press VCR POWER, see if the VCR responds.
4) If there was a response, press RETURN. The operating codes are now set. If there was no response, repeat Step 3.
If you repeat Step 3 a total of 80 times without a response, use the manufacturers remote control which came
with the VCR.
5) Press RETURN to exit.
9
REMOTE CONTROL
(CONTINUED)
DVD setup
The remote control is programmed with DVD codes for power on, power off, play, stop, fast-forward, rewind, previous
chapter, next chapter, tray open/close, and still/pause operation.
1) Find the DVD player brand from the list of codes shown below.
2) Slide the first 2-way selector switch to “TV ” and the other 2-way selector switch to “DVD ”.
3) Press and hold down the DISPLAY button.
4) With the DISPLAY button held down, enter the first code number listed with the 10 key pad.
5) Release the DISPLAY button.
6) Confirm the operation of the DVD player.
• If your DVD player does not respond to the first code, try the others listed. If it does not respond to any code, try
the Search Codes Function as shown below.
• After you program your remote, some DVD buttons may not work properly. If some buttons do not work
properly, use the remote control which came with your DVD player.
DVD Player
CODES
DVD Player
CODES
Aiwa
043
Raite
033
Apex
040
RCA
021, 026
Denon
Hitachi
JVC
020, 037
030, 031
000
Sampo
Samsung
Sharp
034
030
028
Kenwood
Konka
035
039
Silvania
Sony
038
024, 045, 046, 047
Mitsubishi
Onkyo
Oritron
Panasonic
Philips
Pioneer
025
041
044
020
023, 036
022
Technics
Toshiba
Wave
Yamaha
Zenith
020
023
042
020
027, 032
DVD Player Search Codes Function:
1) Slide the first 2-way selector switch to “TV ” and the other 2-way selector switch to “DVD ”.
2) Press the DVD POWER and RETURN buttons. Hold for at least three seconds and release.
3) Press DVD POWER, see if the DVD player responds.
4) If there was a response, press RETURN. The operating codes are now set. If there was no response, repeat Step 3.
If you repeat Step 3 a total of 30 times without a response, use the manufacturers remote control which came with
the DVD player.
5) Press RETURN to exit.
10
ANTENNA/CATV CONNECTIONS
Combination VHF/UHF Antenna
Single 75 ohm Cable
This television has an extended
tuning range and can tune most
cable channels without using a
cable company supplied
converter box. Some cable
companies offer "premium pay
channels" in which the signal is
scrambled. Descrambling these
signals for normal viewing
300 ohm Twin-lead Wire
Take off the Splitter
Splitter
IN
OUT
VIDEO
L/MONO
Y
ANT(75Ω)
VIDEO
L/MONO
A
UHF Antenna
300-75 ohm
Matching Transformer
(not supplied)
PB
requires the use of a descrambler
device which is generally
provided by the cable company.
UDIO
AUDIO
S-VIDEO
PR
R
R
VIDEO
1
VIDEO
2
300 ohm Twin-lead Wire
VHF Antenna
Separate VHF/UHF Antennas
Single 75 ohm Cable
Connect the 75 ohm Cable from the VHF antenna and the UHF
antenna Twin-lead to a combiner (not supplied). Attach the
Combiner to the Antenna Jack.
NOTE:If your VHF antenna has a Twin-lead Wire, use the 300-
75 ohm Matching Transformer (not supplied), then connect the
Transformer to the Combiner.
300 ohm Twin-lead Wire
Combiner
(not supplied)
300-75 ohm
Matching Transformer
(not supplied)
Incoming CATV
For Subscribers to Basic Cable TV Service
For basic cable service not requiring a Converter/Descrambler
box, connect the CATV 75 ohm Coaxial Cable directly to the
Antenna Jack on the back of the television.
Converter/Descrambler
Converter/Descrambler
A
B
For Subscribers to Scrambled Cable TV Service
If you subscribe to a cable service which requires the use of a
Converter/Descrambler box, connect the incoming cable to the
Converter/Descrambler box and connect the output of the box
to the Antenna Jack on the back of the television. Follow the
connections shown left. Set the television to the output of the
Converter/Descrambler box (usually channel 3 or 4) and use
the Converter/Descrambler box to select channels.
Splitter
A/B Switch
Combination VHF/UHF Antenna (Single 75 ohm
Cable or 300 ohm Twin-lead Wire)
Connect the 75 ohm cable from a combination VHF/UHF
antenna to the Antenna Jack. If your combination antenna has
a 300 ohm Twin-lead Wire, use the 300-75 ohm Matching
Transformer (not supplied).
For Subscribers to Unscrambled Basic Cable with
Scrambled Premium Channels
If you subscribe to a cable service in which basic cable
channels are unscrambled and premium channels require the
use of a Converter/Descrambler box, you may wish to use a
two-set signal splitter (sometimes called a "two-set coupler")
and an A/B Switch box from the cable installer or an electronics
supply store. Follow the connections shown left. With the switch
in the "B" position, you can directly tune any nonscrambled
channels on your TV. With the switch in the "A" position, tune
your TV to the output of the Converter/Descrambler box (usually
channel 3 or 4) and use the box to tune scrambled channels.
Combination VHF/UHF Antenna (Separate VHF and
UHF 300 ohm Twin-leads)
Connect the UHF Twin-lead Wire to a Combiner (not supplied).
Connect the VHF Twin-lead to the 300-75 ohm Matching
Transformer (not supplied). Attach the Transformer to the
Combiner. Attach the Combiner to the Antenna Jack.
11
CONNECTION TO OTHER EQUIPMENT
The exact arrangement you use to interconnect various video and audio components to the TV is dependent on the model
and features of each component. Check the User’s Guide provided with each component for the location of video and audio
inputs and outputs.
The connection diagrams in the following are offered as suggestions. You may need to modify them to accommodate your
particular assortment of components. The diagrams are intended to show component video and audio interconnections only.
Press the INPUT button to select the AV mode to use the TV as a monitor.
Operate your VCR as usual.
TV/AV SELECTION
If you connect the TV to VCR, camcorder, TV game or DVD you can select by pressing the INPUT button.
TV
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO 1
Press the INPUT button repeatedly to select the desired
mode.
COMPONENT
An indication of input source will display
on the screen for 4 seconds.
1. To connect the TV to a VCR
3. To connect the TV to a camcorder
To playback from the camcorder, connect the camcorder
to the TV as shown.
(ex. Use VIDEO 1 IN jacks to connect it.)
Rear of TV
VIDEO
IN
OUT
VIDEO
Front of TV
VCR
Y
VIDE
VIDEO 3 IN
AUDIO (L)
PB
L/MONO
L/MONO
AUDIO
VIDEO
L/MONO
AUDIO
R
AUDIO
PR
VIDEO
R
R
VIDEO 1
VIDEO 2
To Audio(L/R)/
Video OUT
To Audio(L/R)/
Video OUT
AUDIO (L)
(not supplied)
AUDIO (R)
AUDIO (R)
(not supplied)
• Select “VIDEO 1” by pressing the INPUT button to
• Select “VIDEO 3” by pressing the INPUT button to
display the VCR picture.
display the camcorder picture.
2. To connect the TV to a VCR with an S-VIDEO jack
If you connect a VCR with an S-video jack to the S-
VIDEO jack on the rear of TV, you must also connect the
audio cables to the AUDIO IN (VIDEO 1) jacks on the
rear of the TV. The S-video cable only carries the video
signal. Audio signal is separate.
4. To connect the TV to a DVD with COMPONENT
VIDEO OUT Jacks.
If you connect a DVD with the COMPONENT VIDEO
OUT jacks to the COMPONENT VIDEO IN (Y, PB, PR)
jacks on the rear of TV, you must also connect the audio
cables to the AUDIO IN (VIDEO 2 IN) jacks on the rear of
the TV.
Rear of TV
AUDIO (L)
Rear of TV
IN
OUT
VIDEO
IN
OUT
VCR
DVD
Y
Y
AUDIO (L)
ANT(75Ω)
VIDEO
VIDEO
PB
L/MONO
L/MONO
AUDIO
L/MONO
AUDIO
AUDIO
S-VIDEO
PR
R
R
R
VIDEO 1
VIDEO 2
VIDEO 1
VIDEO 2
S-VIDEO
(Not supplied)
(Not supplied)
AUDIO (R)
AUDIO (R)
(Not supplied)
(Not supplied)
NOTE: When the S-video cable and the video cable are
connected to each jack at the same time, the S-video
cable takes precedence over the video cable.
• Select “COMPONENT” by pressing the INPUT button
to display the DVD picture.
• If you have a DVD without COMPONENT VIDEO OUT
jacks, connect the video cable to VIDEO IN (VIDEO 2
IN) jack. In this case, select “VIDEO 2” by pressing the
INPUT button to display the DVD picture.
12
SETTING LANGUAGE
This TV can display the channel number, on-screen displays and picture adjustments on the screen in English, Spanish or
French.
On-screen language selection (step 3) will automatically appear on the screen when you press the MENU button initially.
Select the language you prefer first, then proceed with the other menu options.
Press the MENU button.
Press the CH + (L) or – (L)
MENU
CLOCK SET
3
1
2
LANGUAGE / IDIOMA / LANGUE
ON/OFF TIMER
CH SET-UP
button until the " " indicator
points to the desired language:
English (ENGLISH), Spanish
(ESPAÑOL) or French
(FRANCAIS), then press the
ENTER button.
PICTURE
AUDIO
Press the CH + (L) or – (L)
button to select the LANGUAGE
mode, then press the ENTER
button.
LANGUAGE / IDIOMA / LANGUE
V-CHIP SET
L / L / ENTER / MENU / EXIT
L
L
/
/ ENTER / MENU / EXIT
Press the EXIT button.
4
NOTE:
If Spanish or French is chosen, the Closed Caption indicators will be in the selected language, but the Closed Caption text
will not be affected by the language selection.
SETTING CLOCK
You must set the time manually for DISPLAY and ON/OFF TIMER.
Press the MENU button.
Press the CH + (L) or CH – (L) button to set
the minute.
1
2
4
CLOCK SET
10 : 00 AM
Press the CH + (L) or CH –
(L) button until the indicator
next to "CLOCK SET" begins
to flash, then Press the
ENTER button.
MENU
CLOCK SET
ON/OFF TIMER
CH SET-UP
PICTURE
AUDIO
L
L
L
L
/
/
/
/ ENTER / MENU/ EXIT
LANGUAGE / IDIOMA / LANGUE
V-CHIP SET
L / L / ENTER / MENU / EXIT
Press the EXIT button.
5
Press the CH + (L) or CH –
(L) button to set the hour,
then press the VOL + ( )
button.
NOTES:
3
CLOCK SET
12 : 00 AM
• After a power failure or disconnection of the
power plug, the time display will be lost. In this
case, set present time again.
• When you set the minute, you can change in 10-
minutes by holding down the CH + (L) or CH –
(L) button.
L
L
L
L
/
/
/
/ ENTER / MENU/ EXIT
13
TO MEMORIZE CHANNELS
This TV is equipped with a channel memory feature which
allows channels to skip up or down to the next channel set
into memory, skipping over unwanted channels.
Before selecting channels, they must be programmed into
the TV's memory. In addition to normal VHF and UHF
channels, this TV can receive up to 113 Cable TV channels.
To use this TV with an antenna, set the TV/CATV menu
option to the TV setting. When shipped from the factory, this
menu option is in the CATV setting.
AUTOMATIC CHANNEL MEMORY
MENU
CLOCK SET
Press the MENU button.
1
ON/OFF TIMER
CH SET-UP
PICTURE
AUDIO
LANGUAGE / IDIOMA / LANGUE
Press the CH + (L) or – (L) button
2
V-CHIP SET
L / L / ENTER / MENU / EXIT
until the indicator next to "CH SET-
UP" begins to flash, then press the
ENTER button.
CH SET-UP
TV/CATV SELECTION
TV CATV
Press the CH + (L) or – (L) button
3
AUTO CH MEMORY
ADD / DELETE
CH LABEL
until the indicator next to "AUTO CH
MEMORY" begins to flash, then press
the ENTER button. The TV will begin
memorizing all the channels available
in your area.
Press the MENU button.
1
L
L
/
/ ENTER / MENU / EXIT
MENU
Press the CH + (L) or – (L) button
until the indicator next to "CH SET-
AUDIO
UP" begins to flash, then press the
LANGUAGE / IDIOMA / LANGUE
2
CLOCK SET
ON/OFF TIMER
CH SET-UP
PICTURE
V-CHIP SET
ENTER button.
L / L / ENTER / MENU / EXIT
Press the EXIT button.
4
Press the CH + (L) or – (L) button
until the indicator next to "TV/CATV"
begins to flash.
3
TO ADD/DELETE CHANNELS
MENU
CLOCK SET
ON/OFF TIMER
CH SET-UP
PICTURE
Press the MENU button.
1
CH SET-UP
TV CATV
AUDIO
AUTO CH MEMORY
ADD / DELETE
LANGUAGE / IDIOMA / LANGUE
V-CHIP SET
L / L / ENTER / MENU / EXIT
Press the CH + (L) or – (L) button
2
CH LABEL
Press the VOL + ( ) or – ( ) button
to select the TV or CATV mode. The
4
until the indicator next to "CH SET-
UP" begins to flash, then press the
ENTER button.
L
L
L
L
/
/
/
/ MENU / EXIT
arrow indicates the selected mode.
CH SET-UP
TV CATV
5 Press the EXIT button.
AUTO CH MEMORY
ADD / DELETE
CH LABEL
Press the CH + (L) or – (L) button
3
until the indicator next to "ADD/
DELETE" begins to flash, then press
the ENTER button.
L
L
/
/ ENTER / MENU / EXIT
NOTE: Contact your cable company to determine the
type of cable system used in your area.
Select the desired channels to be
added or deleted using the 10-key
pad (0-9) or the CH + or – button.
4
5 Press the VOL + ( ) or – ( ) button to select ADD or
DELETE.
If an unmemorized channel was selected (step 4), the
channel indication will be red. Press the VOL + ( ) or –
( ) button if you wish to ADD the unmemorized
channel. The channel indicator will change from red to
green when a channel is added and the channel will be
memorized. If a memorized channel was selected (step
4), the channel indication will be green.
Press the VOL + ( ) or – ( ) button if
you wish to DELETE the channel from
ADD
CH 012
memory. The channel indicator will
change from green to red when a
channel is deleted.
L
L
L
L
0-9
/
/
/
/ MENU / EXIT
Repeat Steps 4 and 5 for each
channel to be added or deleted.
Press the EXIT button after adding or deleting all of the
desired channels, to return to normal TV viewing.
6
14
TO MEMORIZE CHANNELS
(CONTINUED)
CH LABEL
You can labal every channel up to 4 characters.
Channel labels will appear over the channel number display each time you select a channel.
Select a channel you want to label by pressing
the 10-key pad or CH + or - button.
Go to step 7 when you select the "SET".
Go to step 9 when you select the "CLEAR".
6
7
1
Now the bar for the first space is flashing. Press the
VOL + ( ) or – ( ) button to
Press the MENU button.
2
3
CH LABEL : CH 012
SET/CLEAR
enter a character in the first
Press the CH + (L) or – (L) button until the indicator
SET
space. Press the button
repeatedly until the character
you want appears on the
screen. Then press the ENTER
button.
LABEL ----
next to "CH SET-UP" begins to
MENU
CLOCK SET
flash, then press the ENTER
ON/OFF TIMER
CH SET-UP
button.
L / L /
/
/ENTER / MENU / EXIT
PICTURE
AUDIO
LANGUAGE / IDIOMA / LANGUE
V-CHIP SET
L / L / ENTER / MENU / EXIT
NOTE:
Press the CH + (L) or – (L) button until the indicator
4
5
The character will change as below.
next to "CH LABEL" begins to
flash, then press the ENTER
button.
CH SET-UP
• • •
• • •
–
0
9
A
Z
TV CATV
AUTO CH MEMORY
ADD / DELETE
CH LABEL
+
SPACE
L
L
/
/ ENTER / MENU / EXIT
Repeat step 7 to enter the rest of the characters
from second to fourth.
8
Press the VOL + ( ) or – ( ) button to select "SET"
or "CLEAR". Select "SET" in case
you have a channel to label or
change. Select "CLEAR" in case
you have a channel to delete.
Press the ENTER button to register.
Press the EXIT button.
9
CH LABEL : CH 012
SET/CLEAR
SET CLEAR
10
LABEL ----
Then press the ENTER button.
L / L /
/
/ENTER / MENU / EXIT
15
SETTING V-CHIP
(The V-CHIP function fitted this TV corresponds to the U.S. standard only.)
This TV is fitted with a V-CHIP controller which provides you with channel viewing access controls and restrictions. This
function is to prevent your children from watching violence or sexual scenes that may be harmful.
V-CHIP SET
V-CHIP
TV RATING
MOVIE RATING
CHANGE PASSWORD
1 Press the MENU button and
press the CH + (L) or – (L)
button to select the V-CHIP SET
option, then press the ENTER
button.
4
Press the CH + (L) or – (L)
button to select the V-CHIP
option.
Press the VOL + ( ) or – ( )
button to select the ON.
MENU
CLOCK SET
: OFF
: OFF
: OFF
ON/OFF TIMER
CH SET-UP
PICTURE
AUDIO
LANGUAGE / IDIOMA / LANGUE
V-CHIP SET
L
L
L
L
/
/
/
/
MENU / EXIT
L / L / ENTER / MENU / EXIT
Press the CH + (L) or – (L)
button to select the TV RATING
or MOVIE RATING option.
2
5
6
7
V-CHIP SET
Enter your password (4 digits)
V-CHIP SET
NEW
V-CHIP
: ON
TV RATING
: OFF
using the 10-key pad (0-9). In
the event of entering incorrect
password press the VOL – ( )
button. Then press the ENTER
button.
MOVIE RATING
: OFF
PASSWORD
:
-
CHANGE PASSWORD
L
L
L
L
/
/
/
/ MENU / EXIT
0-9/ / ENTER / MENU / EXIT
Press the VOL + ( ) or – ( )
button to select the desired
rating for the applicable video
or TV channel.
• After registration of password, step 3 will not
appear.
V-CHIP SET
V-CHIP
TV RATING
MOVIE RATING
CHANGE PASSWORD
: ON
: TV-14
: OFF
3
V-CHIP SET
Enter the same password for
confirmation, then press the
ENTER button.
DISPLAY TO SET CONTENTS
CONFIRM
PASSWORD
L
L
L
L
/
/
/
/ MENU / EXIT
:
----
Press the EXIT button.
0-9/ / ENTER / MENU / EXIT
TV RATING
MOVIE RATING
VOL – (
)
VOL + (
TV-PG
)
VOL – (
)
VOL + (
)
TV–Y
TV-Y7
TV-G
TV-14
OFF
TV-MA
G
PG
PG-13
R
R
NC-17
X
OFF
TV-Y : all children
TV-Y7 : 7 years old and above
TV-G : childrens program
: parental guidance
: 14 years old and above
: 17 years old and above
TV-PG
TV-14
TV-MA
: under 17 years old
parental guidance
suggested
G
PG
: all ages
: parental guidance
PG-13 : parental guidance
less than 13 years old
NC-17 : 17 years old and above
: adult only
When you select TV-Y7, TV-PG, TV-14 or TV-MA, press the DISPLAY
button to explain the rating.
X
Press the CH + (L) or – (L) button to select the desired rating you
want. Press the VOL + ( ) or – ( ) button to select the setting ON
or OFF. If you want to back to V-CHIP SET menu, press the MENU
button.
NOTES:
• If you want to change password, follow steps 1 and 2 and select "CHANGE PASSWORD" option then enter your
new password.
• The V-Chip function is activated only on programs and tapes that have the rating signal.
• Once you block a program using the V-Chip function, the blocked program cannot be watched based on the content
of the show. When the program starts, the "IF YOU CANCEL PROTECT, INPUT PASSWORD" will appear on the
screen. When you want to release the V-Chip temporarily, enter the password.
If you change the channel or turn off and on the TV while releasing the V-Chip temporarily, the V-Chip setting will be
resumed.
• When you watch the TV from the cable box or the VCR with the RF Modulator, then you release the V-Chip
temporarily, the V-Chip setting will not be resumed until you turn off the TV. The TV channel is not used in this case.
• When changing the channel with the cable box or the VCR, approximately 10 seconds will pass until the program
appears.
• When you dislocated or lost the password, you can cancel the existing password by the following procedure:
- Press VOLUME – button of main unit.
- Keep pressing VOLUME – button of main unit and press "0" key of remote control simultaneously for a few
seconds.
16
TV BASIC OPERATION
RETURN button
Returns to the channel viewed just before the channel
currently onscreen.
Before operate your TV select TV position of the TV/CATV
switch on the remote to control the TV with the remote.
1
To turn on the TV, press the POWER button.
CH 012
CH 007
2
The VOLUME can be adjusted to a desired level by
pressing the VOL (VOLUME) + or – button.
Adjust the volume level by
pressing the VOLUME + or –
button. The volume level will
be indicated on the screen by
green bar. As the volume level
increases, so do the number of
bar. If the volume decreases,
MUTING button
VOLUME
32
MUTING
The MUTING button instantly turns the
volume down completely when you
press it.
Press MUTING button and the volume
level will instantly go to zero. To restore
the number of green bar also decreases.
the volume to its previous level, press MUTING button again.
The sound level will be indicated on the TV screen by
green bars and a number. As the sound level in-
creases, so do the number of bars and the number on
the screen. The same is true for decreasing the level.
10-key pad (0-9)
Press these buttons to select a channel. The channel
number will appear on the upper right corner of the TV
screen. If an invalid channel number is selected, the display
will revert to the original channel.
Set the TV/CATV menu option to the appropriate
position. When shipped from the factory, this menu
option is in the CATV setting. See "TO MEMORIZE
CHANNELS".
3
4
TV Mode Direct Channel Selection
When the TV/CATV menu option is in the TV position, all
channels can be instantly selected by using two buttons.
(For example, to select channel 2, press "0", then "2". If you
press only "2", channel selection will be delayed for a few
seconds). For channels 10 and above, press the 2 digits in
order.
TV
- VHF/UHF channels
CATV - CABLE TV channels
CH (CHANNEL) + and – buttons
Press and release the CH
CH 012
(CHANNEL) + or – button. The
channel automatically stops at the
next channel set into memory.
CATV Mode Direct Channel Selection
When the TV/CATV menu option is in the CATV position,
channels can be selected as follows:
CH. 1-9
Press "0" twice, then 1-9 as needed.
Example, to select channel 2, press
"002".
Press "0", then remaining 2 digits.
Example, to select channel 12, press
"012".
Press the 2 digits in order.
Example, to select channel 36, press
"36".
For proper operation, before selecting channels,
they should be set into the TV's memory.
See "TO MEMORIZE CHANNELS".
CH. 10-12
CH. 13-99
CH. 100-125 Press the 3 digits in order.
Example, to select channel 120, press
"120".
NOTE: If the station being viewed stops broadcasting, the
TV will automatically shut off after 15 minutes.
17
INPUT button
Selects the signal input source for the
television or Video1,2,3 or Component
for video devices like VCR's, DVD
players, or camcorders.
The input source changes as below.
TV
VIDEO1 VIDEO2
VIDEO
1
VIDEO3
COMPONENT
STEREO AND SEPARATE AUDIO PROGRAM (SAP)
The TV is equipped with a feature known as Multi-channel
LISTENING TO SAP (SEPARATE AUDIO PROGRAM)
When the TV is turned on or a channel selection is
made, make certain the SAP appears on the screen. This
means that the "Separate Audio Program" broadcasting is
available.
TV Sound or MTS. MTS broadcasts greatly enhance TV
viewing by bringing you programs with high fidelity stereo
sound. MTS also provides an extra channel called the
Separate Audio Program or SAP which broadcasters
can use to transmit a second language for bilingual
transmission or for other purposes.
TO SELECT DESIRED SOUND
Press the AUDIO SELECT button to select the desired
sound.
LISTENING TO STEREO SOUND
When the TV is turned on or a channel selection is
made, make certain the STEREO appears on the
screen. This means that "Stereo" broadcasting is avail-
able. You can enjoy stereo sound from the left and right
speakers.
MONO+SAP BROADCASTING
MAIN SOUND
(MONO)
MAIN + SAP SOUND
(MONO)
SAP SOUND
STEREO+SAP BROADCASTING
• When "Mono" broadcasting is received, no indication is
displayed.
MAIN SOUND
(STEREO)
SAP SOUND
• If the broadcast signal is not strong enough or clear
stereo sound is not available, press the AUDIO
SELECT button to change to mono sound. The noise
should be eliminated. Press it again to return to the
stereo sound.
MAIN SOUND
(MONO)
MAIN + SAP SOUND
(MONO)
DISPLAY button
Press the DISPLAY button to display the current informations on the screen.
Press Once
Press Twice
Press 3 times
STEREO and
Separate Audio
Program (SAP)
Channel No.
8 : 30 AM
STEREO SAP
CH 012
ABCD
CLOCK
Channel label
(if preset)
CAPTION CH1
SEL. STEREO
Audio output
Closed Caption
Clear the current
informations
18
PICTURE ADJUSTMENTS
You can adjust the settings for color, sharpness, con-
trast, brightness, tint and component.
Press the VOL + ( ) or – ( ) button to adjust the
setting.
4
Press the MENU button.
1
+
–
increase brightness
increase contrast
be brilliant color
be greenish color
makes picture clearer makes picture softer
be best picture for
DVD
decrease brightness
decrease contrast
be pale color
BRIGHTNESS
CONTRAST
COLOR
TINT
SHARPNESS
2
Press the CH + (L) or – (L)
button until the indicator next to
"PICTURE" begins to flash,
then press the ENTER button.
MENU
CLOCK SET
ON/OFF TIMER
CH SET-UP
be reddish color
PICTURE
AUDIO
LANGUAGE / IDIOMA / LANGUE
V-CHIP SET
indicate video device
except DVD
L / L / ENTER / MENU / EXIT
COMPONET
3
Press the CH + (L) or – (L)
button repeatedly to select the
item you want to adjust.
TO RETURN TO INITIAL SETTING
Press the STANDARD button while the picture adjusting
mode appears on the screen (except the adjusting compo-
nent).
BRIGHTNESS
0
L / L / / MENU / EXIT
/
NOTE: The on-screen display will disappear 6 seconds
after finishing an adjustment. The settings can
only be adjusted when they are displayed on
the TV screen.
BRIGHTNESS
COMPONENT
CONTRAST
COLOR
TINT
SHARPNESS
SOUND ADJUSTMENTS
You can adjust the setting for bass, treble, balance and
stable sound.
Press the VOL + ( ) or – ( ) button to adjust the
setting.
4
+
–
1
2
Press the MENU button.
makes the bass sound makes the bass sound
BASS
stronger
weaker
Press the CH + (L) or – (L)
button until the indicator next to
"AUDIO" begins to flash, then
press the ENTER button.
MENU
CLOCK SET
makes the treble
sound stronger
makes the treble sound
weaker
TREBLE
BALANCE
ON/OFF TIMER
CH SET-UP
makes the output level makes the output level
of right speaker stronger of left speaker stronger
PICTURE
AUDIO
LANGUAGE / IDIOMA / LANGUE
V-CHIP SET
L / L / ENTER / MENU / EXIT
STABLE
SOUND
STABLE SOUND “ON” STABLE SOUND “OFF”
3 Press the CH + (L) or – (L)
button repeatedly to select the
item you want to adjust.
TO RETURN TO INITIAL SETTING
Press the STANDARD button while the sound adjusting
mode appears on the screen.
BASS
0
STABLE SOUND FEATURE
L / L /
/
/ MENU / EXIT
When the loud sound is made, the stable sound feature
automatically lower the sound.
BASS
TREBLE
BALANCE
STABLE SOUND
NOTE: The on-screen display will disappear 6 seconds
after finishing an adjustment. The settings can
only be adjusted when they are displayed on
the TV screen.
19
CLOSED CAPTION
Text: The Text Closed Caption Mode will usually fill 1/2 of
full screen with a programming schedule or other
WHAT IS CLOSED CAPTIONING?
This television has the capability to decode and display
Closed Captioned television programs. Closed
Captioning will display text on the screen for hearing
impaired viewers or it will translate and display text in
another language.
information. After selecting a Closed Caption Mode, it will
stay in effect until it is changed, even if the channel is
changed. If the Captions signal is lost due to a commercial
or a break in the signal, the Captions will reappear when
the signal is received again. If the channels are changed,
the Captions will be delayed approximately 10 seconds.
The Captions will appear in places on the screen where
they will least interfere with the picture, usually on the
bottom of the screen. News programs will usually show
three-line Closed Captions which scroll onto the screen.
Most other shows provide two or three lined Captions
placed near the character who is speaking so the viewer
can follow the dialogue. Words in italics or underlined
describe titles, words in foreign languages or words
requiring emphasis. Words that are sung usually appear
enclosed by musical notes. For television programs
broadcasting with Closed Captions, look in your TV guide
for the Closed Captions symbol (CC).
TO VIEW CLOSED CAPTIONS
Press the C.C. button on the remote control to switch
between normal TV and the two Closed Caption Modes
(Captions and 1/2 of Full Screen Text).
Captions: This Closed Caption Mode will display text on
the screen in English or another language. Generally,
Closed Captions in English are transmitted on Captions
Channel 1 and Closed Captions in other languages are
transmitted on Captions Channel 2.
• When activating the Closed Captioned Decoder, there will be a short delay before the Closed Captioned text appears
on the screen.
• Closed Captioned text is only displayed in locations where it is available.
• If no caption signal is received, no captions will appear, but the television will remain in the Caption Mode.
• Misspellings or unusual characters may occasionally appear during Closed Captioning. This is normal with Closed
Captioning, especially with live programs. This is because during live programs, captions are also entered live.
These transmissions do not allow time for editing.
• When Captions are being displayed, on-screen displays, such as volume and MUTING may not be seen or may
interfere with Closed Captions.
• Some cable systems and copy protection systems may interfere with the Closed Captioned signal.
• If using an indoor antenna or if TV reception is very poor, the Closed Caption Decoder may not appear or may
appear with strange characters or misspelled words. In this case, adjust the antenna for better reception or use an
outdoor antenna.
20
ON/OFF TIMER
ON TIMER SETTING
This feature allows you to have the TV automatically turn "ON" at predetermined time.
If you program the "ON" timer once the timer will turn "ON" the TV daily at the same time and to the same channel.
If the power has been turned on at programmed time, the channel is changed to a programmed one.
Press the MENU button.
Press the CH + (L) or CH –
(L) button to set the
minute, then press the VOL +
( ) button.
1
2
5
ON/OFF TIMER
ON TIMER
7:00AM CH012
CANCEL
CANCEL
Press the CH + (L) or CH – (L)
button until the indicator next to
"ON/OFF TIMER" begins to flash,
then press the ENTER button.
MENU
CLOCK SET
OFF TIMER
12:00AM
ON/OFF TIMER
CH SET-UP
•
You can change in 10-
minutes step by holding
down the CH + (L) or CH –
(L) button.
PICTURE
AUDIO
L / L / L / L / ENTER / MENU / EXIT
LANGUAGE / IDIOMA / LANGUE
V-CHIP SET
L / L / ENTER / MENU / EXIT
Press the CH + (L) or CH – (L)
button until the indicator next to
"ON TIMER" begins to flash, then
press the ENTER button.
3
ON/OFF TIMER
Press the CH+ (L) or CH
–
6
ON/OFF TIMER
ON TIMER
12:00AM CH012
CANCEL
ON TIMER
7:30AM CH012
CANCEL
(L) button to set the channel,
then press the VOL+ ( )
button.
OFF TIMER
12:00AM
CANCEL
OFF TIMER
12:00AM
CANCEL
• You can set the channel
which is added in the
CH SET-UP option.
L / L / ENTER / MENU / EXIT
L / L / L / L / ENTER / MENU / EXIT
4 Press the CH + (L) or CH – (L)
button to set the hour, then press
the VOL + ( ) button.
ON/OFF TIMER
ON TIMER
12:00AM CH012
Press the CH + (L) or CH –
(L) button to select the
SET mode.
CANCEL
7
8
ON/OFF TIMER
ON TIMER
7:30AM CH007
CANCEL
OFF TIMER
12:00AM
CANCEL
L / L / L / L / ENTER / MENU / EXIT
OFF TIMER
12:00AM
CANCEL
L / L / L / L / ENTER / MENU / EXIT
Press the EXIT button.
NOTES:
• You cannot set the ON/OFF TIMER when the clock is not set.
• This TV will automatically turn off approximately 1 hour later after the ON TIMER turns on the TV unless any
buttons are pressed.
• To cancel the ON TIMER function:
To cancel ON TIMER in step 7 above press the CH + (L) or CH – (L) button to select the CANCEL mode.
OFF TIMER SETTING
This feature allows you to have the TV turn "OFF" automatically at a predetermined time.
If you program the OFF TIMER once, The TV will be automatically turned off at the same time daily.
Press the CH + (L) or
Press the MENU button.
4
1
ON/OFF TIMER
ON TIMER
CH – (L) button to set
the hour, then press the
VOL + ( ) button.
12:00AM CH012
CANCEL
CANCEL
2 Press the CH + (L) or CH – (L)
button until the indicator next to
"ON/OFF TIMER" begins to flash,
then press the ENTER button.
MENU
CLOCK SET
OFF TIMER
12:00AM
ON/OFF TIMER
CH SET-UP
PICTURE
AUDIO
L / L / L / L / ENTER / MENU / EXIT
LANGUAGE / IDIOMA / LANGUE
V-CHIP SET
L / L / ENTER / MENU / EXIT
5 Press the CH + (L) or CH –
(L) button to set the minute
then press the VOL + ( )
button.
ON/OFF TIMER
ON TIMER
12:00AM CH012
CANCEL
3
Press the CH + (L) or CH – (L)
ON/OFF TIMER
ON TIMER
7:00AM CH012
CANCEL
OFF TIMER
button until the indicator next to
"OFF TIMER" begins to flash,
then press the ENTER button.
11:00PM
CANCEL
• You can change in 10-
minutes step by holding
down the CH + (L) or CH –
(L) button.
L / L / L / L / ENTER / MENU / EXIT
OFF TIMER
12:00AM
CANCEL
L / L / ENTER / MENU / EXIT
ON/OFF TIMER
Press the CH + (L) or CH –
(L) button to select the SET
mode.
6
ON TIMER
12:00AM CH012
CANCEL
OFF TIMER
11:30PM
CANCEL
L / L / L / L / ENTER / MENU / EXIT
7
Press the EXIT button.
NOTES:
• If station being viewed stops broadcasting, the TV will automatically shut itself off after 15 minutes.
• To cancel the OFF TIMER function:
To cancel OFF TIMER, in step 7 above press the CH + (L) or CH – (L) button to select the CANCEL mode.
21
BBE
By correcting the phase delay and distortion naturally gen- • BBE is a registered trademark of BBE Sound, Inc. For
erated by speaker systems, BBE ensures that the sound
that reaches your ears is as natural as the original
SONUD. Human voices are clearer and music is natural
and well-defined.
U.S., licensed from BBE Sound, Inc. under USP
4638258, 4482866 and 5510572. For Canada, licensed
from BBE Sound, Inc. BBE is a registered trademark of
BBE Sound, Inc.
TO SET BBE
Press the BBE button to select
ON or OFF.
BBE AUDIO
ON OFF
SLEEP TIMER button
The Sleep Timer can turn the TV off for you after you fall
asleep. Program it to work in intervals of 10 minutes, for
a total time of up to 120 minutes.
• To change the sleep timer setting:
Press the SLEEP TIMER button repeatedly until the
display turns to desired time.
• To cancel the sleep time:
Press the SLEEP TIMER button repeatedly until the
display turns to 0.
SLEEP
120
VCR buttons
You can use this remote control to operate the basic
functions of your VCR. These functions include: play,
record, rewind, fast-forward, stop, pause, channel scan,
TV /VCR, power on, and power off.
Move the selector switch to VCR to operate.
• The remote is preset with the code 000 to control
JVC-brand VCR's. For any other manufacturer's brand
VCR, please see the code chart and instructions on
page 9.
DVD buttons
You can also use this remote control to operate the basic Move the selector switch to DVD to operate.
functions of your DVD player. These functions include
play, rewind, fast-forward, stop, still/pause, previous/
next, tray open/close, power on, and power off.
• The remote is preset with the code 000 to control
JVC-brand DVD players. For any other manufacturer's
brand DVD player, please see the code chart and
instructions on page 10.
TV/CATV switch
Use either the television's own tuner or a cable box to
select channels. Set this switch to TV to operate the
television's built-in tuner.
Move the switch to CATV to operate a cable box.
• See page 8 for information on programming your
remote for cable box operation.
VCR/DVD switch
You can control a VCR or DVD player with the buttons
on the lower part of the remote control.
Use the VCR/DVD selector switch to choose either VCR
or DVD operation.
• See pages 9 and 10 for information on programming
your remote with VCR and DVD operating codes.
22
TROUBLESHOOTING GUIDE
Before requesting service, please refer to the following chart for the symptom and possible solution.
SYMPTOMS
POSSIBLE SOLUTIONS
• Make sure the power cord is plugged in.
• Try another AC outlet.
TV does not operate
• Power is off, check fuse or circuit breaker.
• Unplug unit for an hour, then plug it back in.
• Set the TV/VCR switch on the remote control correctly (See page 7).
• Station or CATV experiencing problems, tune to another station.
• Check sound adjustments (Volume and Muting).
• Check for sources of possible interference.
Poor sound or No sound
Poor picture or No picture
• Station or CATV experiencing problems, tune to another station.
• Make sure channels are set into memory.
• Check antenna or CATV connections, reorient antenna.
• Check for sources of possible interference.
• Check picture control adjustments.
• Station or CATV experiencing problems, tune to another station.
• Make sure channels are set into memory.
• Station signal is weak, reorient antenna to receive desired station.
• Check for sources of possible interference.
Poor reception on some channels
Poor color or no color
• Station or CATV experiencing problems, tune to another station.
• Make sure channels are set into memory.
• Check picture control adjustments.
• Check antenna or CATV connections, reorient antenna.
• Check for sources of possible interference.
• Station or CATV experiencing problems, tune to another station.
• Make sure channels are set into memory.
• CATV company is scrambling signal.
Picture wobbles or drifts
No CATV reception
• Check antenna orientation.
• Check all CATV connections.
• Set TV/CATV menu option to the CATV mode.
• Station or CATV system problems, try another station.
• Check antenna connections, reorient antenna.
• Check for sources of possible interference.
Horizontal or diagonal bars on screen
No reception above channel 13
• Make sure TV/CATV menu option is in the appropriate mode.
• If using antenna, check UHF antenna connections.
• Batteries are weak, dead or inserted incorrectly.
• Remote is out of range, move closer to TV within (15 feet).
• Make sure Remote is aimed at sensor.
• Confirm there are no obstructions between the Remote and the TV.
• Make sure the power cord is plugged in.
No Remote operation
TV shuts off
• Set the TV/VCR switch or VCR/DVD switch on the remote control correctly (See page 7).
• No broadcast on station tuned.
• Sleep Timer is set.
• ON/OFF TIMER is set.
• Power interrupted.
• Approximately 1 hour has passed after the ON TIMER turns on and no button was pressed.
• TV station experiencing problems or program tuned is not closed captioned.
Try another channel.
• Check CATV connection or VHF/UHF antenna, reposition or rotate antenna.
• Press C.C. button to turn on the closed caption decoder.
Closed - Caption is not activated.
• Select proper language in the menu options.
Display is not shown in your language.
• Set the TV/VCR switch or VCR/DVD switch on the remote control correctly (See page 7).
• Program remote with a different code.
• The remote control may not be compatible with your product.
• Install new batteries.
The remote control does not operate
other product.
The remote control does not operate
some features of other product.
• Program remote with a different code.
• The remote control may not be able to operate all features of your product.
23
SPECIFICATIONS
AC Power Input:
AC Power Consumption:
Picture Tube:
Audio Power Output Rating:
Speaker:
Audio/Video Input:
120 V, 60 Hz
137W
24" (measured diagonally)
5 W + 5 W
2" x 4-3/4", 8 ohm x 2
COMPONENT Input:
Y-Input:
PB, PR-input:
S-Video Input
1.0Vp-p, 75 ohm
0.7Vp-p, 75 ohm
Y-Input:
C-Input:
1.0Vp-p, 75 ohm
0.3Vp-p, 75 ohm
Video Input:
Audio Input:
181 Channel, Quartz PLL Frequency Synthesized
1.0Vp-p, 75 ohm
–8dB, 47k ohm
Tuner Type:
Receiving Channels:
VHF
2-13
UHF
CATV
14-69
01-97 (5A)-(A-3)
98-99 (A-2)-(A-1)
14-22 (A)-(I)
23-36 (J)-(W)
37-65 (AA)-(FFF)
66-125 (GGG)-(125)
75 ohm (VHF/UHF/CATV) Coaxial Input
26-1/2" (W) x 19-1/8" (D) x 20-1/8" (H)
72.6 lbs
Antenna Input Impedance:
Dimensions:
Weight:
ACCESSORIES:
Remote Control
Batteries (2 x AA)
Specifications are subject to change without notice.
JVC COMPANY OF AMERICA
Division of U.S. JVC CORP.
1700 Valley Road
JVC CANADA, INC.
21 Finchdene Square
Scarborough, Ontario
Canada M1X 1A7
Wayne, New Jersey 07470
3J50301A K
01/01
PRINTED IN THAILAND
|