Philips TV Converter Box slvs400 User Manual

Wireless TV link  
EN  
SLV5400  
Welcome  
Quick start guide  
Connect transmitter  
Connect receiver  
Enjoy  
1
2
3
 
Connect transmitter  
1
Connect theVCR or DVD recorder  
A
VCR  
DVD recorder  
If you have noVCR or DVD recorder,  
proceed with the next step  
TV1  
1. Take the supplied transmitter (A)  
2
3
2. Find the SCART cable from theVCR or  
DVD recorder that is connected to TV1.  
3. Unplug the SCART cable from TV1.  
4. Plug the SCART cable into the 4-VCR/DVD  
RECORDER port on the transmitter (A).  
1
4
1
3
4
TV1  
2
Connect your other video source  
B
1. Find the SCART cable from your other  
video source that is connected to TV1.  
2. Unplug the SCART cable from TV1.  
3. Plug the SCART cable into the correspon-  
ding SCART port on the transmitter (A):  
1-SAT:  
1-STB:  
2-AUX:  
Satellite receiver  
Set top box  
Any auxiliary device  
3-DVD PLAYER: DVD player  
4. Repeat this for each other video source.  
Connect TV1  
C
1. Take the supplied SCART cable (D).  
2. Plug one end into the TV1 SCART port on  
the transmitter (A).  
1
3
TV1  
2
4
2
3. Plug the other end into the SCART port of  
the TV.  
TV1  
3
1
 
Firmly insert the SCART cables to the ports:  
1. Plug the connector straight into the port.  
2.Apply some force when you insert the connector.  
Connect the power adapter  
D
L
DC 12V  
1. Take the supplied power adapter (E).  
2. Plug the connector into the DC 12V power  
connector on the transmitter (A).  
Channel  
1 2 3 4  
R
3. Plug the adapter into the power outlet.  
> The power light on the front comes on as red.  
2
3
1
AC  
Check the operation of TV1  
E
1. Switch on TV1.  
2. Switch on the connected video source.  
3. Select the correct SCART input on TV1.  
4. Check if TV1 shows the image of the video source.  
> The transmitter is connected correctly.  
Connect receiver  
2
Preparation  
A
1. Switch on the transmitter (A).  
2. Switch on the video source.  
3. Take these items:  
STANDBY  
SELECT  
Receiver (B)  
Remote control (C)  
Remote control of a video source.  
SCART cable (D)  
SLVRELESS TV LINK TRANSMITTER  
Power adapter (E)  
1
This quick start guide (F)  
4. Go to TV2.  
 
Connect TV2  
B
TV2  
2
1. Take the supplied SCART cable (D).  
2. Plug one end into the TV2 SCART port on  
the receiver.  
3. Plug the other end into the SCART port of  
the TV.  
1
3
TV2  
Connect the power adapter  
C
1. Take the supplied power adapter (E).  
2. Plug the connector into the DC 12V power  
connector on the receiver (B).  
DC 12V  
3. Plug the adapter into the power outlet.  
> The power light on the front comes on as red.  
2
3
1
AC  
Check the operation of TV2  
D
1. Switch on TV2.  
TV2  
2. Switch on the receiver (B).  
3. Select the correct SCART input on TV2.  
4. Point the remote control of the video  
source to the receiver (B).  
1
5. Operate the video source with its remote  
control.  
2
6. Check if TV2 shows the image of the video  
source.  
WIRELESS TV LINK RECEIVER  
4
5
> The receiver is connected correctly.  
 
Result  
TV2  
TV1  
SAT/STB  
AUX  
DVD player  
VCR  
DVD recorder  
Enjoy  
3
Example:View satellite programs on TV2  
A
TV1  
Your satellite receiver needs to be connected  
to the transmitter (A) of the wireless TV link.  
1
1. Switch on the transmitter (A).  
2. Switch on TV2.  
TV2  
3. Switch on the receiver (B).  
4. Select the correct SCART input on TV2.  
5. Point the remote control of the satellite  
receiver to the receiver (B).  
2
3
6. Switch on the satellite receiver.  
7. Operate the satellite receiver with its  
remote control. Enjoy!  
WIRELESS TV LINK RECEIVER  
5
6
7
To view other video sources, replace ´Satellite  
receiver´ with the name of the device used.  
View video source on TV1  
Remotely control the wireless TV link  
B
C
1. Switch on TV1.  
1. Remove the protective foil from the  
2. Select the correct SCART input on TV1.  
3. Operate the video source as usual. Enjoy!  
supplied remote control (C).  
2. Point the remote control (C) at the wireless  
TV link (A or B).  
3. Select the video source.  
4. Operate the video source as usual. Enjoy!  
 
Troubleshooting  
Problem  
Tip  
No image or wrong image on TV1  
Make sure video sources are connected to the transmitter (A).  
Make sure the transmitter (A) is connected to TV1.  
Make sure SCART cables are firmly inserted.  
Make sure the video source is switched on.  
Make sure the correct SCART input on TV1 is selected.  
Select the correct video source with TV1 source.  
> See the user manual (H) page 8.  
No image or wrong image on TV2  
Make sure SCART cables are firmly inserted.  
Make sure the receiver (B) is connected to TV2.  
Make sure both receiver (B) and transmitter (A) are switched on.  
Make sure the video source is switched on.  
Make sure the correct SCART input on TV2 is selected.  
Select the correct video source with +/- on the receiver (B).  
If the video source gives proper image on TV1:  
Make sure the video source gives video signal in CVBS mode.  
> See its user manual  
Change the wireless channel that is used for communication.  
> See the user manual (H) page 7.  
The receiver (B) is out of range of the transmitter (A).  
The number of walls and ceilings in between the receiver (B) and  
transmitter (A) restrict the distance.  
Interference in the image on TV2  
Slightly change the position of the receiver (B) or the transmitter (A).  
Change the wireless channel that is used for communication.  
> See the user manual (H) page 7.  
The receiver (B) is out of range of the transmitter (A).  
The number of walls and ceilings in between the receiver (B) and  
transmitter (A) restrict the distance.  
The video sources do not respond  
to the remote control commands  
from TV2  
Point the remote control directly to the receiver (B).  
Replace the batteries of the remote controls with new ones.  
Install the remote control blaster cord (G).  
> See the user manual (H) page 6.  
The maximum operating distance of the remote control is 5 m.  
The image of the video source  
disappears on TV2  
Turn off the auto standby mode of the video source.  
> See its user manual.  
Follow the instructions to reconnect the videosources.  
> See this quick start guide (F).  
 
Need help?  
User manual  
See the user manual that came with your wireless TV link.  
Helpline  
België/Belgique/Belgien 070 222 303 (0.17)  
Danmark  
Deutschland  
España  
3525 8759  
0900 1101211 (0.12)  
902 888 784 (0.15)  
08 9165 0005 (0.23)  
0 0800 3122 1280  
01 764 0292  
France  
Ireland  
Italia  
899 23 45 06 (0.25)  
Luxemburg/Luxembourg 40 6661 6544  
Nederland  
Norge  
Österreich  
Portugal  
0900 8407 (0.20)  
2270 8111  
0900 060 827 (0.20)  
2 1359 1442  
Schweiz/Suisse/Svizzera 0900 001 600  
Suomi  
Sverige  
0600 412 001  
08 5792 9100  
UK (United Kingdom)  
0906 1010 016 (£ 0.15)  
Specifications are subject to change without notice.  
Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners.  
2005 © Koninklijke Philips Electronics N.V.All rights reserved.  
QSG-SLV5400-AEN-V1.0  
 

Philips Car Stereo System CDC 775 User Manual
Philips Clock Radio AJ 3040 00P User Manual
Philips Digital Photo Frame SPF5008 User Manual
Philips Ventilation Hood PPX2450 User Manual
Philips Work Light P 5759 D User Manual
Polycom Telephone IP 500 501 SIP 16 User Manual
Poulan Lawn Mower 177552 User Manual
Poulan Snow Blower 418962 User Manual
Premier Mounts Indoor Furnishings PBC UMW User Manual
PYLE Audio DVD Player PLPK65TVD User Manual