Avital Universal Remote 5303 User Manual

Model 5303

➤Owner’s Guide

ING, REPAIR, REPLACEMENT, DAMAGES FOR LOSS OF TIME, LOSS OF

EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY

AND THE LIKE. NOTWITHSTANDING THE ABOVE, MANUFACTURER

DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CON-

TROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on

how long an implied warranty will last or the exclusion or limitation of incidental or con-

sequential damages. This warranty gives you specific legal rights, and you may also have

other rights which vary from state to state.

Make sure you have all of the following information from your dealer:

A clear copy of the sales receipt, showing the following:

■ Date of purchase

■ Your full name and address

■ Authorized dealer's company name and address

■ Type of alarm installed

■ Year, make, model and color of the automobile

■ Automobile license number

■ Vehicle identification number

■ All security options installed on automobile

■ Installation receipts

Table of contents

Limited lifetime consumer warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i

Standard transmitter configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

What is included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Important information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

System maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Your warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Fcc/id notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Caution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Transmitter functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Standard configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Using your system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Warning! Safety first . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Active arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Passive arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Multi-level security arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Arming while driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Disarming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

High security disarm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Disarming without a transmitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Silent mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Panic mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Valet mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Remote start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Rear defogger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Valet take-over. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Short-run/turbo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Safety features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Starter anti-grind circuitry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Disabling the remote start system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Shut down inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Nuisance prevention® circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Arming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Disarming diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

System status chirps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Table of zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Interpreting zone diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Code hopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

High frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Owner recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Rapid resume logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Power saver mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Programming options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Security & convenience expansions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Glossary of terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Quick reference guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Standard transmitter configuration

controls the Arm and Panic On/Off function.

controls the Disarm and Panic Off function.

controls Silent Mode™ and Auxiliary trunk output.

controls the Remote Start function.

and

pressed together control the Timer mode.

pressed together control Turbo/Short Run.

pressed together control auxillary 4 output.

pressed together control auxillary 5 output.

and

pressed together control the rear

defogger.

and

pressed together control auxillary 6 output.

and

control Temperature check.

controls Daily start on/off.

and

controls Temperature start on/off.

What is included

➤

A control module

A transceiver/antenna

Two four-button transmitters

A Stinger™ DoubleGuard two-stage shock sensor

A Revenger™ Soft Chirp™ six-tone programmable siren

A status LED indicator light

A push-button Valet button

Your warranty registration

A shut-down toggle switch

Important information

Congratulations on the purchase of your combination remote

start alarm system. Due to the complexity of this system, it must

be installed by an authorized dealer only. Installation of this

product by anyone other than an authorized dealer voids the

warranty. All dealers are provided with a preprinted dealer certif-

icate to verify authorization.

By carefully reading this Owner's Guide prior to using your

system, you will maximize the use of this system and its features.

You can print additional or replacement copies of this manual by

accessing our web site at www.directed.com.

System maintenance

➜

The system requires no specific maintenance beyond remote

battery replacement. The remote is powered by a 1.5V AAA

battery.

The battery level indicator has three level indicators that serve as

a visual indication of battery charge. When the battery reaches a

low charge level that requires replacment, the remote generates

a single notification chirp, and the battery level indicator flashes

continuously.

Battery Replacement

Gently pull the battery cover release tab, thenslide the door

down to expose the baattery and remove the expired battery.

Place the new battery into the remote observing the correct

polarity. When power is returned the remote lights all icons in

the LCD and gnerates all beeper tones at once.

Your warranty

➜

Your warranty registration must be completely filled out and

returned within 10 days of purchase. Your product warranty

will not be validated if your warranty registration is not returned.

Make sure you receive the warranty registration from your dealer.

It is also necessary to keep your proof of purchase, which reflects

that the product was installed by an authorized dealer.

Fcc/id notice

➜

This device complies with Part 15 of FCC rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause

undesirable operation.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to

operate this device.

Caution

➜

This product is designed for fuel injected, automatic transmis-

sion vehicles only. Use of this product in a standard transmission

vehicle is dangerous and contrary the product's intended use.

Transmitter functions

The receiver uses a computer-based Learn Routine to learn the

transmitter buttons. This makes it possible to assign any remote

transmitter button to any receiver function. The transmitter

initially comes programmed with Standard Configuration, but

may also be customized by an authorized dealer. The buttons in

all of the instructions in this manual correspond to a Standard

Configuration transmitter.

Standard configuration

➜

Button

The arming and panic functions are controlled by pressing this

button for one second.

Button

The disarming function is controlled by pressing this button for

one second.

Button

Silent Mode™ and an optional auxiliary function are controlled

by this button. (Silent Mode works by pressing this button for

less than one second before arming or disarming. An optional

auxiliary function, such as trunk release, can be controlled by

pressing this button for 1.5 seconds.)

The auxiliary output controls __________________________.

Button

The remote start function of your system is controlled by

pressing this button twice within 3 seconds.

and

Buttons

An optional auxiliary convenience or expansion function that

you have added to your system can be activated by pressing these

buttons simultaneously.

The auxiliary output controls __________________________.

and

Buttons

An optional auxiliary convenience or expansion function that

you have added to your system can be activated by pressing these

buttons simultaneously.

The auxiliary output controls __________________________.

and

Buttons

The remote start timer mode is controlled by pressing these

buttons simultaneously. The 2-way remote produces a melody

and the clock indicator appears on the remote's LCD. Once in

timer mode the system remote starts every 24-hours. Repeat this

procedure to turn Timer Mode off.

and

Buttons

The short-run turbo mode is activated when these buttons are

pressed simultaneously.

and

Buttons

When simultaneously pressed these buttons control the rear

window defogger during remote starting.

and

Buttons

An optional auxiliary convenience or expansion function that

you have added to your system can be activated by pressing these

buttons simultaneously.

The auxiliary output controls __________________________.

and

This system reports the interior temperature of your vehicle by

pressing these buttons sequentially.To activate the temperature

display press the above three buttons. You hear a melody and the

interior temperature is displayed on the LCD screen for five

seconds.

Note: If the ignition is on, the temperature check

clockmode will not work.

and

Buttons

While the system is armed, press simulataneously to enter

temperature auto statt mode. The vehicle is automatically

restarted if the interior temperature drops below 0 degrees

Fahrenheit.

Note: Disarming the system while in temperature

autostart mode casuses the system to exit this mode.

Using your system

Warning! Safety first

➜

The following safety warnings must be observed at all times:

➤

Due to the complexity of this system, installation of this

product must only be performed by an authorized Directed

dealer.

When properly installed, this system can start the vehicle via

a command signal from the remote control transmitter.

Therefore, never operate the system in an enclosed area or

partially enclosed area without ventilation (such as a garage).

When parking in an enclosed or partially enclosed area or

when having the vehicle serviced, the remote start system

must be disabled using the installed toggle switch. It is the

user's sole responsibility to properly handle and keep out of

reach from children all remote control transmitters to assure

that the system does not unintentionally remote start the

vehicle. THE USER MUST INSTALL A CARBON

MONOXIDE DETECTOR IN OR ABOUT THE

LIVING AREA ADJACENT TO THE VEHICLE. ALL

DOORS LEADING FROM ADJACENT LIVING AREAS

TO THE ENCLOSED OR PARTIALLY ENCLOSED

VEHICLE STORAGE AREA MUST AT ALL TIMES

REMAIN CLOSED. These precautions are the sole respon-

sibility of the user.

➤

Use of this product in a manner contrary to its intended

mode of operation may result in property damage, personal

injury, or death. (1) Never remotely start the vehicle with the

vehicle in gear, and (2) Never remotely start the vehicle with

the keys in the ignition. The user must also have the neutral

safety feature of the vehicle periodically checked, wherein the

vehicle must not remotely start while the car is in gear. This

testing should be performed by an authorized Directed dealer

in accordance with the Safety Check outlined in the product

installation guide. If the vehicle starts in gear, cease remote

start operation immediately and consult with the authorized

Directed dealer to fix the problem.

➤

After the remote start module has been installed, contact

your authorized dealer to have him or her test the remote

start module by performing the Safety Check outlined in the

product installation guide. If the vehicle starts when

performing the Neutral Safety Shutdown Circuit test, the

remote start unit has not been properly installed. The remote

start module must be removed or the installer must properly

reinstall the remote start system so that the vehicle does not

start in gear. All installations must be performed by an autho-

rized Directed dealer. OPERATION OF THE REMOTE

START MODULE IF THE VEHICLE STARTS IN GEAR

IS CONTRARY TO ITS INTENDED MODE OF OPER-

ATION. OPERATING THE REMOTE START SYSTEM

UNDER THESE CONDITIONS MAY RESULT IN

PROPERTY DAMAGE OR PERSONAL INJURY. YOU

MUST IMMEDIATELY CEASE THE USE OF THE

UNIT AND SEEK THE ASSISTANCE OF AN AUTHO-

RIZED DIRECTED DEALER TO REPAIR OR

DISCONNECT THE INSTALLED REMOTE START

MODULE. DIRECTED WILL NOT BE HELD

RESPONSIBLE OR PAY FOR INSTALLATION OR

REINSTALLATION COSTS.

Active arming

➜

You can arm the system by pressing

of your transmitter for

one second. When the system arms, you will hear a short siren

sound, or chirp, and see the parking lights flash once. If the power

door locks are controlled by the system, the doors will also lock.

While the system is armed, the status LED will flash approxi-

mately once per second, indicating that the system is actively pro-

tecting your vehicle. If you hear a second chirp after arming and

note that the status LED is flashing in groups, see the Diagnostics

Section of this guide. This extra chirp is called Bypass Notification.

Passive arming

➜

The system can be programmed to arm itself automatically (called

passive arming). If the system is programmed for passive arming, it

will automatically arm 30 seconds after the ignition is turned off

and the system detects that you have left the vehicle by opening and

closing a door. Whenever the system is in its 30-second passive

arming countdown, the status LED will flash twice as fast as it does

when the system is armed. At the 20-second point of the count-

down, the siren will chirp to indicate that the system is about to

arm. At the 30-second point, the parking lights will flash to indicate

that the system is armed.

Note: If any protected entry point (such as a door or a

switch-protected trunk or hood) is open, the system will

not passively arm (unless forced passive arming is pro-

grammed on. See Programming Options section).

When armed your vehicle is protected as follows:

➤

Light impacts trigger the Warn Away signal. When trig-

gered, the siren chirps and the parking lights flash for a few

seconds.

➤

Heavy impacts trip a Triggered Sequence. The sequence

consists of the siren sounding continuously and the parking

lights flashing for a pre-programmed period, which can range

in duration from 1 to 180 seconds.

➤

If a door is opened, the system will immediately start

chirping the siren and flashing the parking lights. Three

seconds later, the siren output changes to a continuous blast.

This progressive response gives you time to disarm the system

with your transmitter if you inadvertently open the door

while the system is armed, while still providing instant re-

sponse (even if the door is immediately closed).

Turning on the ignition key will trip the same progressive re-

sponse as opening a door.

➤

The optional starter kill prevents the vehicle’s starter from

cranking.

Multi-level security arming

➜

Multi-Level Security Arming allows you to select which of the

system's inputs or sensors will be active and which will be

bypassed when the system is armed. (See Table of Zones section of

this guide.) Pressing (only in Standard Configuration) again

within five seconds of arming the system will activate the Multi-

Level Security feature. Each time is pressed again, a different

security level is selected. The different security levels are selected

as follows:

➤

Press

once: The siren chirps once. The system is armed.

a second time within five seconds: The siren chirps

twice followed by a long chirp. Zone 2 is now bypassed.

Press a third time within five seconds: The siren chirps

three times followed by a long chirp. Zone 4 is now bypassed.

Press a fourth time within five seconds: The siren chirps four

times followed by a long chirp. Zones 2 and 4 are now bypassed.

Press a fifth time within five seconds: The siren chirps

➤

five times followed by a long chirp. All input zones, except

the ignition, are now bypassed.

Note: Multi-Level Security Arming only applies to a sin-

gle arming cycle. Once the system is disarmed and then

re-armed, all the zones will be active again.

Arming while driving

➜

Your security system can be armed while driving the vehicle!

Simply press

on the transmitter for two seconds while the

vehicle is running. The siren will chirp once to indicate that the

security system is armed, and then once more to indicate that the

ignition is on. The system will not respond to any input except

the door triggers, and the starter kill relay (if installed) will not

be activated. Once you have arrived at your destination, the

system will disarm when the ignition is turned off. The siren will

chirp twice and the LED will then stop flashing. The system can

also be disarmed at any time by pressing

Disarming

➜

To disarm the security system, press

. You will hear two

chirps, and the parking lights will flash twice. If the power locks

are controlled by the system, the doors will also unlock. The

siren chirping either four or five times when disarming indicates

Tamper Alert, which is described in the Diagnostics Section of

this guide.

High security disarm

➜

This security system offers High Security Disarm. High Security

Disarm is a feature that makes it possible to silence and reset the

system while it is triggering, without disarming the system. If the

system is triggered and the siren has been sounding for longer

than six seconds, pressing

on the remote transmitter will

stop the trigger and return the unit to the armed state. The

system will not disarm, but rather reset. This prevents you from

disabling the system should you wish to disarm it without visu-

ally checking the vehicle. Pressing

after resetting the system

will disarm the system; pressing this button during the first six

seconds of the triggered sequence will disarm the security system

immediately. The six second timer is provided for your conve-

nience, in case the system is accidentally triggered.

Disarming without a transmitter

➜

If your remote transmitter is lost or damaged, you can manually

disarm your vehicle security system. To disarm the system

without a transmitter, you must have the vehicle's ignition key

and know where the Valet switch is located. Be sure to check

with your installer at the time of installation for both the location

and the preset response (1-5 presses) of the Valet switch.

To disarm the security system,

turn the ignition to the ON posi-

tion. Press the Valet button the

preset number of times (one to

DRW-35

five times) within 15 seconds.

After five seconds, the system will

disarm. If the system does not

disarm, you may have waited too

long; turn the ignition off and on

and try again.

Location of Valet Button_________________________________

Number of Presses_____________________________________

Important! The Valet button can be programmed to

respond to 1-5 presses for the disarm function. You must

check with the installer to verify the programming for

your individual unit.

Silent mode

➜

To temporarily turn off the arm or disarm chirps, use Silent

Mode™. Simply press

for less than one second before

arming or disarming, and the confirmation chirp(s) will be elim-

inated for that one operation only. If you want the arm/disarm

chirps turned off permanently, your dealer can do this for you.

Note: The Warn Away® response to lighter impacts is

bypassed if the system is armed using Silent Mode. This

ensures that no chirps will be emitted by the siren in an

area you want chirp-free. The system is still fully capable

of triggering. Only the Warn Away® response is

bypassed.

Panic mode

➜

If you are threatened in or near your vehicle, you can attract

attention by triggering the system with your transmitter. Just

press

for two seconds, and you will enter Panic Mode. The

siren will sound and the parking lights will flash for the

programmed siren duration. To stop Panic Mode at any time,

press

on the remote transmitter again.

Valet mode

➜

You can prevent your security system from automatically arming

and triggering by using Valet Mode. This is very useful when

washing the vehicle or having it serviced. In Valet Mode, the

security system will not arm, even with the remote transmitter,

but all convenience functions (door locks, trunk release, etc.) will

continue to work normally.

To enter or exit Valet Mode:

1. Turn the ignition on.

2. Turn the ignition off.

DRW-35

3. Press and release the Valet

button within 10 seconds.

The status LED will light solidly if you are entering Valet Mode,

and it will go out if you are exiting Valet Mode.

To enter or exit Valet Mode using the transmitter:

1. Open any vehicle door.

2. Press

3. Press

4. Press

again.

The status LED will light solidly if you are entering Valet Mode,

and it will go out if you are exiting Valet Mode.

Remote start

➜

This feature allows you to remotely start and run your vehicle for

a programmable period of time. This makes it possible to warm

up the engine, as well as adjust the interior temperature of the ve-

hicle with the climate control system. If interior heating or

cooling is desired, the climate controls must be preset, and the

fan blower must be set to the desired level prior to remote starting

the vehicle.

Important! (1) Never remote start your vehicle when the

keys are in the ignition, except when performing Valet

Take-Over, and (2) Never start the vehicle if it is not in

either PARK or NEUTRAL.

To remote start the vehicle:

1. Press

on the transmitter twice within 3 seconds.

2. The parking lights flash to confirm that the vehicle will

attempt to start.

3. In gasoline vehicles, the engine starts 4 seconds after the

parking lights flash. In diesel vehicles, the engine starts when

the WAIT-TO-START indicator on the vehicle's dash goes

out or the programmed delay has ended.

4. Once the vehicle has started, it runs for the pre-programmed

period of time (either 12, 24, or 60 minutes - see

Programming Options section of this guide) or until a shut-

down input is triggered.

Important! It is unsafe to operate a vehicle’s motor in a

garage or other closed off area. Breathing the exhaust

from the vehicle is hazardous to your health. Never acti-

vate the remote start in an enclosed space.

When you are ready to drive the vehicle:

1. Insert the ignition key and turn

it to the ON (not START) posi-

tion.

2. Press the brake pedal.

Note: If the brake pedal is pressed before the key is in the

ON position, the engine will shut down.

While the vehicle is running during remote start operation, the

system will monitor the vehicle and will automatically shut down

the engine if the system receives any of the following

shut-down inputs:

➤

The brake pedal is pressed.

The hood is opened.

The shutdown toggle switch is put into the OFF position.

The pre-programmed run time (12, 24, or 60 minutes) has

elapsed.

➤

Transmitter buttons

is pressed twice within 3 seconds.

Rear defogger

➜

To turn the rear defogger output OFF:

1. Simultaneously press & release the

on the remote control.

buttons

2. The lights will flash 2 times.

3. The rear defogger output will no longer activate when the

vehicle is remote started.

Note: If the remote start is on the parking lights will turn

off then flash 2-times before returning to their normal

output and the defogger output, if active, will cease.

To turn the rear defogger output ON:

1. Simultaneously press & release the

on the remote control.

buttons

2. The lights will flash 3 times.

3. The rear defogger output will once again activate when the

vehicle is remote started.

Note: If the remote start is on the lights will turn off then

flash 3-times before returning to their normal output and

the defogger output will activate as programmed.

Note: If the temperature is greater than 55° F at the time

of remote start activation, the rear defogger will not acti-

vate for that start.

Valet take-over

➜

The Valet Take-Over feature allows the vehicle to remain running

after the key has been removed from the ignition. This feature is

useful for occasions when you wish to exit and lock the vehicle

for short periods of time, but would like to leave the motor

running and the climate controls on.

To perform Valet Take-Over:

1. Before turning off the engine, press and release

twice

within 3 seconds on the transmitter (or press and release the

optional momentary switch). Then wait five seconds.

2. Turn the ignition key to the OFF position. (The engine will

stay running.)

3. The engine will run until the pre-programmed time elapses

or a shut-down input is received. (See the previous Remote

Start section for a complete list of shut-down inputs.)

Note: This feature will not work if the brake pedal is

being pressed.

Short-run/turbo

➜

Short run turbo mode keeps the engine running after arriving at

you destination for a programmable period of 1, 3, 5 or 10

minutes. This allows the system’s timer to conveniently cool

down the turbo after you have left the vehicle.

To activate:

1. Park the vehicle and set parking brake.

2. Remove your foot from the brake pedal and leave the engine

running.

3. Press and release the

time.

and

buttons at the same

4. The lights will flash to indicate the remote start has entered

short run turbo mode.

5. Turn off the key, the engine will keep running.

6. Exit and secure the vehicle.

7. The engine will turn off after the programmed run time.

Safety features

This system has several important safety features to ensure proper

operation of the motor and prevent accidental damage to the

engine or its components.

Starter anti-grind circuitry

➜

Whenever the vehicle is remote started, advanced anti-grind

circuitry prevents the starter from engaging, even if the key is

turned to the start position. This prevents damage to the starter

motor if the key is turned to the start position during remote start

operation.

Disabling the remote start system

➜

This feature allows your system's remote start unit to be

temporarily disabled to prevent the vehicle from being remote

started accidentally. This feature is useful if the vehicle is being

serviced or stored in an enclosed area. To disable the remote start,

move the shutdown toggle switch to the OFF position. The

switch can be installed in a location of your choice. Check with

your installer for recommended locations.

Location of Shutdown Switch____________________________

Shut down inputs

➜

This security system uses several inputs to shut down the remote

start operation of the motor or prevent remote start if certain

inputs are active. The two most important are hood and brake

inputs. The hood input will prevent the motor from starting, as

well as shut it down, any time the hood is opened. The brake

pedal will shut down the motor at any time during remote start

operation, as well as preventing the remote start from activating

while it is being pressed.

Nuisance prevention^®circuitry

➜

Your system has Directed’s Nuisance Prevention Circuitry

(NPC). It prevents annoying repetitive trigger sequences due to

faulty door pin switches or environmental conditions such as

thunder, jackhammers, airport noise, etc.

Example

If the alarm triggers three times within a 60-minute period and

each time the same sensor or switch triggers the alarm, NPC will

interpret those triggers as false alarms. After the third trigger,

NPC ignores, or bypasses, that sensor or switch (along with any

other sensors or switches sharing the same zone) for 60 minutes.

If the bypassed sensor tries to trigger the security system while it

is being bypassed, the 60-minute bypass period will start over.

This ensures that a sensor that is continually being triggered will

remain bypassed.

The vehicle doors are protected by NPC differently. If your secu-

rity system is triggered by an open door for three full cycles, the

system will bypass the doors until the trigger ceases.

Note: Arming and disarming the system does not reset

this function! The only ways to reset a bypassed zone are

for it to not trigger for 60 minutes, or to turn on the igni-

tion. If testing your system, it is important to remember

that the NPC programming can cause zones to be

bypassed and appear to stop working. If five chirps are

heard when disarming, NPC has been engaged. If you

wish to clear the NPC memory, turn the ignition on.

Diagnostics

The microprocessor at the heart of your system is constantly

monitoring all of the switches and sensors connected to it. It is

designed to detect any faulty switches and sensors and prevents

them from disabling the entire system. The microprocessor will

also record and report any triggers that occurred during your

absence. Refer to the System Status Chirps and Table of Zones

sections of this guide for diagnostic information.

Arming diagnostics

➜

If the security system is armed at the same time that an input is

active (such as a door opening or sensor triggering), you will hear

one siren chirp to indicate arming and a second siren chirp to

indicate Bypass Notification. A Bypass Notification chirp means

that the security system ignores the input that was active when

the system was armed, until that input ceases. Three seconds after

that input ceases, the security system will resume normal moni-

toring. For example, if your vehicle has an interior light exit delay

and you arm your security system before the interior light turns

off, you may hear a second Bypass Notification chirp. Once the

light turns off, however, the security system resumes normal

monitoring.

Note: Bypass Notification does not occur when the sys-

tem is in Silent Mode or if the notification chirps have

been programmed off by the installer.

Disarming diagnostics

➜

Extra chirps that are heard when disarming the system are the

Tamper Alert. If four chirps are heard when disarming the

system, then the security system was triggered in your absence. If

five chirps are heard when disarming the system, a zone was trig-

gered so many times that the Nuisance Protection Circuitry has

bypassed that zone. In either case, the status LED will indicate

which zone was involved (see Table of Zones section). The security

system will retain this information in its memory and chirp four

or five times each time it is disarmed, until the next time that the

ignition is turned on.

System status chirps

➜

The siren will chirp when arming/disarming the system. The

pattern of chirps will audibly report the system’s status as

described below.

Action

Number of Chirps

Description

Arm

System armed

Arm

1 (3-second delay), 1

System armed with

Bypass Notification

Disarm

System disarmed

System disarmed with

Tamper Alert

Disarm

System disarmed NPC

active

Table of zones

➜

A zone is represented by the number of LED flashes used by the

system to identify a particular type of input. Standard input

assignments are listed in the following table, along with spaces to

write in any optional sensors or switches that have been installed.

ZONE

(Number of

DEALER-INSTALLED

OPTIONS

LED Flashes)

DESCRIPTION

Trunk Pin

Instant trigger - a heavier impact

detected by the shock sensor

Door switch trigger

Instant trigger - for optional

sensors

Ignition trigger

Hood Pin

Interpreting zone diagnostics

➜

Warn Away responses are not reported by arming or disarming

diagnostics. If you receive a Bypass notification when arming or

a Tamper Alert notification when disarming, look at the LED.

Active or triggered zones will be indicated by a pattern of blinks

by the LED.

Example

If zone 3 was active or triggered, the LED will blink three times

with a two-second pause. Then it will blink three times again,

and repeat until the ignition is turned on.

Note: Your system stores the last two triggered zones in

memory. If your system has been triggered but the LED

has been reset by turning on the ignition, your dealer can

still recall the last two zones that were triggered. Contact

your dealer for details.

Code hopping

The receiver and transmitters use a mathematical formula called

an algorithm to change their code each time the transmitter is

used. This technology has been developed to increase the secu-

rity of the unit. The control unit knows what the next codes should

be. This helps to keep the transmitter “in sync” with the control

unit even if you use the remote control out of range of the

vehicle. However, if the remote has been pressed many times out

of range of the vehicle, or the battery has been removed, it may fall

out of sync with the control unit and fail to operate the system.

To re-sync the remote simply press

several times within

range of the vehicle. The alarm will automatically re-sync and

respond to the transmitters normally.

High frequency

Your system transmits and receives at 434 MHz. This provides a

cleaner spectrum with less interference and a more stable signal.

Enjoy a phenomenal increase in range, even in areas with high

radio interference.

Owner recognition

Owner Recognition is a revolutionary new feature available only

from Directed. Using a Directed Bitwriter , hand-held program-

ming tool, your dealer can program many of the system settings.

The programmer makes it possible to program different settings

for each transmitter that is used with the system. Then, whenev-

er a specific transmitter is used, the system will recall the settings

assigned to that transmitter. Owner Recognition lets up to four

users of the system have different settings that meet their specific

needs. It is almost like having four separate alarms in your

vehicle, one for each user.

Note: Owner Recognition cannot be programmed with-

out a Bitwriter^®and the necessary software. Check with

your dealer for more information.

Rapid resume logic

This Directed system will store its current state to non-volatile

memory. If power is lost and then reconnected the system will

recall the stored state from memory. This means if the unit is in

Valet Mode and the battery is disconnected for any reason, such

as servicing the car, when the battery is reconnected the unit will

still be in Valet Mode. This applies to all states of the system

including arm, disarm, and Valet Mode.

Power saver mode

Your system will automatically enter Power Saver Mode while

armed or in Valet Mode, after a period of time in which no oper-

ation has been performed. This lowers the current draw on the

vehicle's battery. Power Saver Mode takes over under the

following conditions:

➤

Power Saver when the system is armed: After the system has

been armed for 24 hours the LED will flash at half its

normal rate, decreasing the system's current draw.

➤

Power Saver in Valet Mode: When the system enters Valet

Mode the LED illuminates steadily. If the vehicle is not used

(ignition is not turned on) for a one hour period while the

system is in Valet Mode, the LED will shut off. If the system

remains in Valet Mode, the LED will come back on the next

time the ignition is turned on and then back off.

Programming options

Programming options control your system's normal, operational

set-up. Most options do not require additional parts, but some

may require installation labor.

The following is a list of the programmable options, with the

factory settings in Bold.

➤

Active arming (transmitter only) or passive arming (auto-

matic arming 30 seconds after the last door has been closed).

Arming/disarming siren chirps on or off.

➤

The ignition controlled door lock feature on or off: When

this feature is programmed on, the doors will lock three

seconds after the ignition is turned on, and unlock when the

ignition is turned off. If your installer is programming the

security system with the Directed Bitwriter , ignition lock

and unlock are independent features that can be

programmed separately.

➤

Passive door locking (with passive arming) or active door

locking (only when arming with the transmitter). Passive

locking allows the vehicle's doors to lock when the security

system passively arms (after the 30-second countdown). This

feature only works if passive arming has been programmed.

Panic mode enabled/disabled when the ignition is turned

on. (Some states have laws against sirens sounding in moving

cars.)

➤

Forced passive arming on or off. If your security system is

programmed for passive arming and the forced passive

arming feature has been programmed on, the system will

passively arm after one hour, even if a protected entry has

been left open. Forced passive arming ensures that the

system will be armed if a door has accidentally been left ajar

when leaving the vehicle.

Note: When the system passively arms after one hour, the

entry point that has been left open, and anything con-

nected to the same zone, is bypassed and cannot trigger

the system. However, the remaining inputs to the system

are fully operational.

➤

Full trigger response 30 or 60 seconds: This determines how

long the full triggered sequence lasts. Some states have laws

regulating how long a security system can sound before it is

considered a nuisance. If your installer is programming the

security system with the Directed Bitwriter , the full trig-

gered response can be programmed for any duration ranging

from 1 to 180 seconds.

Note: This feature will only function if the FailSafe

Starter Kill relay has been installed.

™

➤

Siren tones and chirp volume. The output of the Revenger

™

Soft Chirp siren consists of six different tones in sequence.

Any of these tones can be eliminated by a dealer, resulting in a

unique, easily identifiable siren sound. The chirps can be either

full volume or 6 decibels quieter than the full alarm blast.

12, 24, or 60 minute run time. your system can be

programmed to allow the vehicle to run for 12, 24, or 60

minutes when remote started. Can be set up to minute

increments by your installer.

➤

3, 6, 9, or 12 minute timer mode run time. Your system can

be programmed to allow the vehicle to run for 3, 6, 9, or 12

minutes when remote started in timer mode. Can be set up

to 16 minutes by your installer.

➤

While the remote start system is running the engine, the

parking lights of the vehicle can flash on and off or come on

and light steadily.

Comfort closure is a programming option which closes the

vehicle’s windows after remote locking.

Security & convenience expansions

Listed below are some of the many expansion options available.

Please consult your dealer for a complete explanation of all the

options available to you.

Audio Sensor: Metal on glass, glass cracking, and breaking

glass produce distinctive acoustic signatures. The 506T audio

sensor uses a microphone to pick up sounds, then analyzes them

with proprietary acoustic software to determine if the glass has

been struck.

Field Disturbance Sensor: An invisible dome of coverage is estab-

lished by installing the 508D “radar” sensor. Your system can

react to any intrusions into this field with the full triggered

sequence.

Power Locks: This system offers lock outputs that can control

some manufacturers' power door lock systems. For other

systems, additional parts may be required.

Power Trunk Release: The accessory output of the system can op-

erate a factory power release for the vehicle’s trunk or hatch.

Although the on-board relay can control most power trunk re-

leases, sometimes an optional relay is required. If the factory

release is not power-activated, Directed 's 522T trunk release

solenoid can often be added.

Power Window Control: Automatic power window control is pro-

vided with the 529T and 530T systems. These can operate

power windows, and can roll them up automatically when the

system is armed, roll them down, or both up and down.

Glossary of terms

Control Unit: The “brain” of your system. Usually hidden under-

neath the dash area of the vehicle. The control unit houses the

microprocessor which monitors your vehicle and controls all

system functions.

Input: A physical connection to the system. An input can be

provided by a sensor, pinswitch or by existing systems in the

vehicle, such as ignition or courtesy lights.

LED: A red light mounted at a discretionary location inside the

vehicle. It is used to indicate the status of your system.

Shock Sensor: This system has a dual zone shock sensor. This

sensor is mounted in the vehicle and designed to pick up impacts

to the vehicle or glass.

Transmitter: A hand-held, remote control which operates the

various functions of your system.

Trigger or Triggered Sequence: This is what happens when the

alarm “goes off” or “trips.” The triggered sequence of your

system consists of the siren sounding and parking lights flashing

for the programmed duration.

Valet button: A small push button mounted at a discretionary

location inside the vehicle. It is used to override the starter inter-

rupt when a transmitter is lost or damaged, or to enter or exit

Valet Mode.

Warning Zone Response: Lighter impacts to the vehicle will

generate the Warning Zone response. It consists of several

seconds of siren chirps and parking light flashes.

Zone: A zone is a separate input that the alarm can recognize as

unique. Each input to the system is connected to a particular

zone. Often two or more inputs may share the same zone.

Quick reference guide

Arming

■

To arm, press

. When the system arms, you will hear a short chirp, and

the parking lights will flash once.

Arming while driving

To arm the system while driving, press

■

on your transmitter while the

vehicle is running. The system will chirp once and then once more to indi-

cate that the ignition is on.

Arming while driving

To arm the system while driving, press

■

on your transmitter while the

vehicle is running. The system will chirp once and then once more to indi-

cate that the ignition is on.

Disarming

To disarm, press

flash twice.

■

. You will hear two chirps, and the parking lights will

High security disarm

■

For high security disarm, press

on your transmitter and the siren will stop

sounding. To completely disarm the security system, press again and the

system will chirp 4 or 5 times (reporting the trigger).

Disarming without a transmitter

■

Turn on the ignition. Press the Valet button within 15 seconds. The system

should now disarm. If it does not, you may have waited too long, so turn the

ignition off and on and try again.

Silent Mode^™

Pressing

tion chirp(s) for that one operation only.

■

briefly before arming or disarming will eliminate the confirma-

Panic Mode

Press

and the parking lights will flash for 30 seconds. To stop Panic Mode at any

time, press on the transmitter again.

■

for 2 seconds, and you will enter Panic Mode. The siren will sound

To remote start the vehicle

Press twice within 3 seconds. The parking lights will turn on (if

■

connected) and the vehicle will start and run for the programmed period of

time.

To disable the remote start system

■

To disable the remote start, move the shutdown toggle switch to the OFF

position.

Location of Valet button_________________________________

Number of Valet button pulses for disarming_______________

Valet Takeover

■ Press and release

on the transmitter twice in 3 seconds. Turn the

ignition key to the OFF position. Once the vehicle has started, it will run

for the pre-programmed period of time (12, 24, or 60 minutes).

Rear Window Defogger

■ Press the

, and

buttons simultaneously to turn the defog-

ger on or off when remote starting. When a remote start is initiated, the

parking lights will flash 2-times if the defogger is set to off, and will

flash 3-times if the defogger is set to on.

The company behind this system is Directed Electronics

Since its inception, Directed Electronics has had one purpose, to provide consumers with

the finest vehicle security and car stereo products and accessories available. The recipient of

nearly 100 patents and Innovations Awards in the field of advanced electronic

technology, Directed is ISO 9001 registered.

Quality Directed Electronics products are sold and serviced throughout North America

and around the world.

Call (800) 274-0200 for more information about our products and services.

Directed Electronics is committed to delivering world class quality products

and services that excite and delight our customers.

Vista, CA 92081

www.directed.com

G5303L 2008- 07

ACP EP Memory Computer Drive CISURF MBM 1G User Manual
ACTiSYS Computer Accessories ACT IR2000UL User Manual
AllTrade Air Compressor 835534 User Manual
American Standard Plumbing Product 192 User Manual
AO Smith Water Heater ADM 115 User Manual
Atlantic Indoor Furnishings 160 DVD User Manual
Avery Battery Charger 9465 User Manual
Axis Communications Security Camera axis communications dome network camera User Manual
Axor Plumbing Product 4438XX0 User Manual
Azden Barcode Reader PCS 9600D User Manual