BenQ Computer Monitor T52WA User Manual

T52WA  
15’’ Wide-Screen LCD Monitor  
User Manual  
 
1. Package contents  
1. LCD Monitor  
2. Monitor Base (the shape of base may vary according to  
the monitor model)  
3. Power Cord (plug may vary according to the electrical  
standards for your area)  
4. Analog Signal Cable  
5. Quick Installation Guide  
6. CD-ROM (contains user manual)  
Package contents  
3
 
 
2. Installation  
To connect the monitor to your PC  
1. Make sure that the PC and monitor are unplugged.  
2. Connect the signal cable to the monitor and the PC.  
To connect the monitor to the power source  
Connect the separate power cable to the monitor and a grounded outlet.  
4
Installation  
 
     
3. Adjusting your monitor  
Functions of the buttons and indicator  
Item  
Function  
Enter OSD menu, select item, enter submenu, and confirm recall.  
1. Positive adjustment, change within several selections.  
Enter  
X
2. Hot key of "Brightness".  
1. Minus adjustment, change within several selections.  
W
2. Hot key of "Contrast".  
Leave menu, cancel recall. (Settings will be saved automatically after  
adjustments are made.)  
Exit  
Hot key of auto adjustment (for geometric settings only).  
Auto  
OSD icon list  
Icon  
Function  
Description  
Auto Adjust  
* Optimize the picture performance automatically  
Luminance  
Geometry  
Color  
* Select "Brightness" and "Contrast" adjustment submenu  
* Select "H. Position", "V. Position", "Pixel Clock" and "Phase"  
adjustment submenu  
* Select color temperature or to set up user mode  
* Adjust the position and time of OSD menu on the screen  
* Select your own preference of language of OSD menu  
* Reset monitor parameters back to factory preset value  
* Select "Miscellaneous" adjustment submenu  
* Adjust the luminance of the screen  
OSD  
Language  
Recall  
Miscellaneous  
Brightness  
Contrast  
H. Position  
* Adjust the contrast level of the screen  
* Shift the screen left or right  
Adjusting your monitor  
5
 
     
V. Position  
Pixel Clock  
Phase  
* Shift the screen up or down  
* Adjust the monitor internal sampling clock rate  
* Adjust the monitor internal signal phase  
OSD H. Position * Shift the OSD left or right  
OSD V. Position  
OSD Time  
Sharpness  
DDC/CI  
* Shift the OSD up or down  
* Set OSD display duration time  
* Adjust the sharp level of the screen  
* Switch "DDC/CI" On or Off  
* Show the display information  
Information  
6
Adjusting your monitor  
 
4. Troubleshooting  
Symptom  
Remedy  
*Blank Screen*  
Power indicator is off  
Make sure the power cable is connected properly (see  
Make sure that the monitor was turned on using the  
Power indicator lights orange  
Power indicator lights green  
Perhaps a power saving mode is active? Press any key  
on your keyboard or move the mouse.  
A screen saver may have activated automatically after a  
certain period of inactivity. Press any key on your key-  
board or move the mouse.  
"No Signal Detected!" message  
Is the signal cable connected to the monitor and the  
PC's graphics port (see Installation on page 4)?  
Is the PC turned on (see your PC's documentation)?  
*Display Problems*  
Image is displaced to the left/right  
or to the top/bottom  
If the image appears normal but off-center, you can  
adjust it using the OSD functions. For further informa-  
tion, see "Auto Adjust" in the OSD icon list section.  
Image is blurred  
Check brightness and contrast settings (see "Lumi-  
nance" in the OSD icon list section).  
Check the sharpness setting (see "Sharpness" in the  
OSD icon list section).  
Color problems  
If the colors are off (e.g., white is not really displayed as  
white etc.), you should adjust the color temperature  
(see "Color" in the OSD icon list section).  
Troubleshooting  
7
 
 
5. Specifications  
15’’ Wide-Screen LCD monitor  
Item  
T52WA  
Display Size  
Pixel Pitch  
332.16 (H) x 186.84 (V) mm  
0.2595 (H) x 0.2595 (V) mm  
Panel  
Monitor  
Display Colors  
16.7M colors  
Horizontal: 31 - 64 KHz  
Input Signal  
Frequency  
Vertical: 59 - 75 Hz  
D-sub 15 pin  
-5° - 20°  
Connector  
Tilt  
Analog  
Tilt Angle  
Dimensions  
Net  
370.3(W) x 330.4(H) x 137.1(D) mm  
(W x H x D)  
Weight  
Net  
< 4 kg  
AC  
AC 100-240V, 50 Hz / 60 Hz  
Active: < 21W / Standby: < 2W  
Power  
Consumption  
8
Specifications  
 
   

Black Decker Trimmer 90556152 User Manual
Boston Acoustics Speaker RX47 User Manual
BOXLIGHT Projector MP 650i User Manual
Briggs Stratton Battery Charger PC300 User Manual
Carrier Heating System 06 User Manual
Carrier Heat Pump 38QF User Manual
Carson Optical TV Mount ED1928 User Manual
Cateye Elliptical Trainer ECL 3200 User Manual
C Crane Portable Radio CCRadio plus User Manual
Chamberlain Garage Door Opener PD420 2 User Manual