Compact disc player
User’s manual
2
CD5/CD10
Your music + our passion
CD 5
CD10
Important safety instructions
For your own safety please read the following important safety instructions
carefully before attempting to connect this unit to the mains power supply.
They will also enable you to get the best performance from and prolong
the life of the unit:
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
The lightning flash with the arrowhead symbol within an equilateral
triangle is intended to alert the user to the presence of un-insulated
‘dangerous voltage’ within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
4. Follow all instructions.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance instructions
in the service literature relevant to this appliance.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
The symbol on this product indicates that it is of CLASS II
(double insulated) construction.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
WEEE symbol
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
The crossed-out wheeled bin is the European Union symbol for
indicating separate collection for electrical and electronic
equipment. This product contains electrical and electronic
equipment which should be reused, recycled or recovered and
should not be disposed of with unsorted regular waste. Please return the
unit or contact the authorised dealer from whom you purchased this
product for more information.
9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A
grounding-type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly
at plugs, convenience receptacles and the point where they exit from
the apparatus.
CE mark
This product complies with European Low Voltage
(2006/95/EC), Electromagnetic Compatibility (2004/108/EC) and
Environmentally-friendly design of Energy-using Products (2005/32/EC)
Directives when used and installed according to this instruction manual.
For continued compliance only Cambridge Audio accessories should be
used with this product and servicing must be referred to qualified service
personnel.
11. Only use attachments/accessories specified by the manufacturer.
12. Use with only the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for
long periods of time.
C-Tick mark
This product meets the Australian Communications Authority’s
Radio communications and EMC requirements.
14. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as the
power-supply cord or plug having been damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate normally, or has
been dropped.
Ross Test Stamp
This product meets Russian electronic safety approvals.
FCC regulations
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR
TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER AUTHORITY
TO OPERATE THE EQUIPMENT.
WARNING
– To reduce the risk of fire or electric shock, do not expose this unit to
rain or moisture.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
– Batteries (battery pack or batteries installed) shall not be exposed to
excessive heat such as sunshine, fire or the like.
protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
The unit must be installed in a manner that makes disconnection of the
mains plug from the mains socket outlet (or appliance connector from the
rear of the unit) possible. Where the mains plug is used as the disconnect
device, the disconnect device shall remain readily operable. Only use the
mains cord supplied with this unit.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
Please ensure there is ample ventilation (at least 10cm clearance all
round). Do not put any objects on top of this unit. Do not situate it on a rug
or other soft surface and do not obstruct any air inlets or outlet grilles. Do
not cover the ventilation grilles with items such as newspapers,
tablecloths, curtains, etc.
– Re-orient or relocate the receiving antenna.
This unit must not be used near water or exposed to dripping or splashing
water or other liquids. No objects filled with liquid, such as vases, shall be
placed on the unit.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
3
Limited warranty
Cambridge Audio warrants this product to be free from defects in
materials and workmanship (subject to the terms set forth below).
Cambridge Audio will repair or replace (at Cambridge Audio's option) this
product or any defective parts in this product. Warranty periods may vary
from country to country. If in doubt consult your dealer and ensure that
you retain proof of purchase.
Ventilation
IMPORTANT - The unit will become hot when in use. Do not stack multiple
units on top of each other. Do not place in an enclosed area such as a
bookcase or in a cabinet without sufficient ventilation.
Ensure that small objects do not fall through any ventilation grille. If this
happens, switch off immediately, disconnect from the mains supply and
contact your dealer for advice.
To obtain warranty service, please contact the Cambridge Audio
authorised dealer from which you purchased this product. If your dealer is
not equipped to perform the repair of your Cambridge Audio product, it
can be returned by your dealer to Cambridge Audio or an authorised
Cambridge Audio service agent. You will need to ship this product in either
its original packaging or packaging affording an equal degree of
protection.
Positioning
Choose the installation location carefully. Avoid placing it in direct sunlight
or close to a source of heat. No naked flame sources, such as lighted
candles, should be placed on the unit. Also avoid locations subject to
vibration and excessive dust, cold or moisture. The unit can be used in a
moderate climate.
Proof of purchase in the form of a bill of sale or receipted invoice, which is
evidence that this product is within the warranty period, must be
presented to obtain warranty service.
This unit must be installed on a sturdy, level surface. Do not place in a
sealed area such as a bookcase or in a cabinet. Do not place the unit on
an unstable surface or shelf. The unit may fall, causing serious injury to a
child or adult as well as serious damage to the product. Do not place other
equipment on top of the unit.
This Warranty is invalid if (a) the factory-applied serial number has been
altered or removed from this product or (b) this product was not
purchased from a Cambridge Audio authorised dealer. You may call
Cambridge Audio or your local country Cambridge Audio distributor to
confirm that you have an unaltered serial number and/or you purchased
from a Cambridge Audio authorised dealer.
Due to stray magnetic fields turntables or CRT TVs should not be located
nearby due to possible interference.
This Warranty does not cover cosmetic damage or damage due to acts of
God, accident, misuse, abuse, negligence, commercial use, or
modification of, or to any part of, the product. This Warranty does not
cover damage due to improper operation, maintenance or installation, or
attempted repair by anyone other than Cambridge Audio or a Cambridge
Audio dealer, or authorised service agent which is authorised to do
Cambridge Audio warranty work. Any unauthorised repairs will void this
Warranty. This Warranty does not cover products sold AS IS or WITH ALL
FAULTS.
Electronic audio components have a running in period of around a week
(if used several hours per day). This will allow the new components to
settle down, the sonic properties will improve over this time.
Power sources
The unit should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power-supply to your
home, consult your product dealer or local power company.
REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY ARE
THE EXCLUSIVE REMEDY OF THE CONSUMER. CAMBRIDGE AUDIO SHALL
NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY IN THIS
PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY LAW, THIS WARRANTY
IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED
WARRANTIES WHATSOEVER INCLUDING, BUT NOT LIMITED TO, THE
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PRACTICAL
PURPOSE.
To turn the unit off, switch off at the front panel. If you do not intend to
use this unit for a long period of time, unplug it from the mains socket.
Overloading
Do not overload wall outlets or extension cord as this can result in a risk
of fire or electric shock. Overloaded AC outlets, extension cords, frayed
power cords, damaged or cracked wire insulation, and broken plugs are
dangerous. They may result in a shock or fire hazard.
Some countries and US states do not allow the exclusion or limitation of
incidental or consequential damages or implied warranties so the above
exclusions may not apply to you. This Warranty gives you specific legal
rights, and you may have other statutory rights, which vary from state to
state or country to country.
Be sure to insert each power cord securely. To prevent hum and noise, do
not bundle the interconnect leads with the power cord or speaker leads.
Cleaning
To clean the unit, wipe its case with a dry, lint-free cloth. Do not use any
cleaning fluids containing alcohol, ammonia or abrasives. Do not spray an
aerosol at or near the unit.
For any service, in or out of warranty, please contact your dealer.
Battery disposal
Please dispose of any discharged batteries according to local
environmental/electronic waste disposal guidelines.
Plug Fitting Instructions (UK Only)
Loudspeakers
The cord supplied with this appliance is factory fitted with a UK mains plug fitted
with a 5 amp fuse inside. If it is necessary to change the fuse, it is important that
a 5 amp one is used. If the plug needs to be changed because it is not suitable for
your socket, or becomes damaged, it should be cut off and an appropriate plug
fitted following the wiring instructions below. The plug must then be disposed of
safely, as insertion into a mains socket is likely to cause an electrical hazard.
Should it be necessary to fit a 3-pin BS mains plug to the power cord the wires
should be fitted as shown in this diagram. The colours of the wires in the mains
lead of this appliance may not correspond with the coloured markings identifying
the terminals in your plug. Connect them as follows:
Before making any connections to loudspeakers, make sure all power is
turned off and only use suitable interconnects.
Servicing
These units are not user serviceable, never attempt to repair, disassemble
or reconstruct the unit if there seems to be a problem. A serious electric
shock could result if this precautionary measure is ignored. In the event
of a problem or failure, please contact your dealer.
The wire which is coloured BLUE must be
connected to the terminal which is marked
with the letter ‘N’ or coloured BLACK.
The wire which is coloured BROWN must be
connected to the terminal which is marked
with the letter ‘L’ or coloured RED.
The wire which is coloured GREEN/YELLOW
must be connected to the terminal which is
marked with the letter ‘E’ or coloured GREEN.
If a 13 amp (BS 1363) plug is used, a 5 amp fuse must be fitted, or if any other
type of plug is used a 5 amp fuse must be fitted, either in the plug or adaptor, or
on the distribution board.
4
CD 5
CD10
Rear panel connections
Manufactured in an
ISO9001 approved facility
L i n e O u t p u t
Left
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference; 2) This device must accept any interference,
including interference that may cause undesired operation.
Designed and engineered in London, England
Class
Luokan
Klass
1
Laser Product
Laserplaite
Laserapparat
Topaz CD10 Compact Disc Player
Rated Power Consumption: 15W
Mains Voltage Selector Switch
115V/230V AC~50/60Hz
1
1
t
L e f
Digital Output
S/P DIF Co-axial
Power AC
2
R i g h t
Right
3
1
Caution
Serial Number Label Removed
Line Output
Made under licence in China
2
1
S/P DIF co-axial digital output (CD10 only)
Line Output
For input to a separate DAC, such as Cambridge Audio DacMagic*, or
digital recording machine. To obtain best results, use a high quality
75ohm digital RCA interconnect cable (not one designed for normal audio
use).
Use good quality interconnect cables from these sockets to any line level
input on your amplifier. For best results and matched performance, we
recommend connection to a Cambridge Audio amplifier.
3
AC power socket
* For more information, see the DacMagic page on the Cambridge Audio
website: www.cambridgeaudio.com/products.php
Once you have completed all connections to the amplifier, plug the AC
power cable into an appropriate mains socket and turn the unit on. Your
compact disc player is now ready for use.
Front Panel controls
3
1
2
4
5
6
7
4
1
On/Off
Open/Close
Switches the unit on and off.
Allows you to open and close the disc tray. After placing a CD in the tray,
press Open/Close to close the tray.
2
Infrared sensor
5
Play/Pause
Receives IR commands from the supplied remote control. An
unobstructed line of sight between the remote control and the sensor is
required.
Plays the disc and pauses play.
6
Stop
3
Display
Stops the CD playing.
Alpha-numeric characters which display playback information. On
inserting a disc, the CD player will take a few seconds to read the Table of
Contents (TOC) information from the disc. The display will then show the
number of tracks on the CD and the total length of the CD.
7
Skip/Scan
Enables you to skip between and search within tracks. Press briefly to skip
a track. Press and hold to scan through a track.
5
Remote control
The Topaz CD5 and CD10 are supplied with a remote control that operates
the unit. In addition, the Blue coloured buttons can operate a matching
Topaz AM10 amplifier or SR10 stereo receiver.
Always use a CR2025 Lithium coin cell.
Open/Close
Opens and closes the disc tray.
Numerical track select
Press the number of the desired track. The track will then play
automatically from the start of the track.
Prog
Allows you to program a unique sequence of up to 20 tracks. Refer to
‘Operating Instructions’ section of this manual for more information.
Prog Clear
Clears a programmed sequence. See later section of this manual.
ꢀ Pause/ꢁ Stop/ꢂ Play
Press the relevant button to pause, stop or play the CD.
ꢃ ꢄ Skip
Right Skip – Press to skip forward by one track on the CD.
Left Skip – Press to skip backward by one track on the CD.
ꢅ ꢆ Scan
Press and hold to scan within the selected track. Press the right button to
fast forward, the left button to rewind.
Random, Repeat, Remain
Read the ‘Operating Instructions’ section of this manual for information on
the functions of these buttons.
AM10/SR10 (Blue coloured icons)
To operate the Topaz AM10 or SR10 unit only.
ꢇ
Adjust the volume on a SR10/AM10.
Changes source on a SR10/AM10.
Mutes the output of a SR10/AM10.
Note: These controls work on the Topaz SR10/AM10 only and are not
compatible with Cambridge Audio Azur amplifiers/receivers or units from
other manufacturers.
6
CD 5
CD10
Operating instructions
4. To turn the Repeat function off, press the Repeat button either before
or during playback until ‘RPT OFF’ appear on the display.
Loading and unloading discs
1. Press the Open/Close button.
2. When the disc tray has opened fully, place a disc carefully in the tray
with the label side facing up.
Playing tracks in random order
1. Ensure that a disc is loaded.
3. To close the disc tray, press the Open/Close button again. When the
tray, with a correctly loaded disc, is fully closed the CD player will read
the disc and display the content information.
2. Press the Random button on the remote control. ‘RAN ON’ will appear
on the display.
4. The disc tray can be opened at any time by pressing the Open/Close
button. Only remove the disc after the tray has fully opened.
Note:
– Do not put anything except a compact disc into the tray. Foreign objects
may damage the mechanism.
3. Press ꢂ. The CD player will now play the entire disc in random order. It
is also possible to press the Random button during playback to listen to
tracks in random order.
– Do not force the tray by hand during the opening and closing operations.
4. Press the Random button to exit. The disc will continue playing to the
end in the correct order.
– To avoid dirt and dust entering the mechanism, keep the disc tray
closed.
– If the compact disc is badly scratched or too dirty, the player may not be
able to read it or play it.
– Never load more than one disc into the disc tray at any time.
5. Press the ꢁ button at any time to stop the disc.
Normal disc play
Note: Selecting ‘Random’ mode when ‘RPT ONE’ has been selected will
automatically cancel ‘RPT ONE’ mode.
This unit has been designed to play compact discs,
recordable CDs (CD-R) and re-writable CDs (CD-RW) bearing
the identification logo shown here. No other discs can be
used. The CD-R/CD-RW discs should contain properly
recorded TOC (Table of Contents) information so that they can be played
back. This unit can play only the discs recorded in the CDDA format
designed for music reproduction or those containing MP3 or WMA files.
Do not attempt to play a disc on this unit containing other data, such as a
data CD-ROM for PCs.
Using the Remain function
1. Ensure that the disc is playing.
2. Press the Remain button on the remote control once to display the time
remaining for the track playing.
3. Pressing the Remain button the second time will show the total
remaining disc time.
1. Switch on your amplifier and set its input selector to the correct
position. Adjust the volume control to a minimum.
4. Press the Remain button again either before or during playback to
return to normal play mode.
2. Press the Open/Close button to open the disc tray and load a disc.
3. Press the Open/Close button again to close the tray. The CD player will
read the disc.
Programming disc play
It is possible to program the CD5/CD10 to play back in any order only the
tracks you wish to listen to.
4. To begin playback, press the ꢂ button.
1. Ensure that a disc is loaded. The display should show the TOC data.
5. When the last track has finished playing, the display will return to Table
of Contents (TOC).
2. Press the Prog button on the remote control. The Program set-up will
appear on the display.
6. To stop the disc at any point, press the ꢁ button. Pressing the ꢀ
button while the disc is playing will pause the disc. Playback can be
resumed by pressing ꢂ button.
Locating a specific track during playback
1. A single short press of the ꢄ button will take you to the beginning of
3. Use the ꢃ ꢄ buttons or enter the track number that you want to
the next track on the CD. Repeat as necessary.
program as your first track.
2. A single short press of the ꢃ button will take you to the beginning of
the previous track.
4. Press the Prog button on the remote. The desired track is now
programmed. The program number automatically increases by one for
the next entry.
Locating a specific track when playback is stopped
1. A single short press of the ꢃ ꢄ buttons will skip between tracks.
2. Press ꢂ to start playback from the selected track.
Repeating discs and tracks
1. Ensure that the disc is loaded.
5. Repeat steps three and four until all your desired tracks are entered. A
maximum of 20 tracks can be programmed.
6. Press the ꢂ button to begin programmed playback.
2. To repeat a specific track, press the Repeat button on the remote. ‘RPT
ONE’ will appear on the display. Press ꢂ and the selected track will
now repeat until the function is turned off. Alternatively, press the
Repeat button, select the chosen track using the numerical buttons on
the remote control and press ꢂ.
7. Press the Prog Clear button on the remote to clear all programmed
tracks.
3. Press the Repeat button twice on the remote control. ‘RPT ALL’ will
appear on the display. Press ꢂ. The whole disc will now be repeated
until the function is turned off.
7
Technical specifications
CD5
CD10
D/A Converter
Wolfson Microelectronics WM8725
2-pole Butterworth filter
D/A Converter
Wolfson Microelectronics WM8761
2-pole Butterworth filter
Filter
Filter
Frequency response (+/-0.4dB) 20Hz - 20kHz
Frequency response (+/-0.4dB) 20Hz - 20kHz
THD @ 1Khz 0dBFs
THD @ 1Khz -10dBFs
S/N ratio, A weighted
Crosstalk @1kHz
<0.006%
<0.015%
>93dB
THD @ 1Khz 0BFs
THD @ 1Khz -10dBFs
S/N ratio, A weighted
Crosstalk @1kHz
<0.006%
<0.01%
>95dB
<-95dB
<-98dB
<-95dB
<50ohms
Crosstalk @20kHz
Output impedance
<-95dB
Crosstalk @20kHz
Output impedance
<50ohms
Maximum power consumption 15W
Maximum power consumption 15W
Dimensions
75 x 430 x 305mm
(3.0 x 16.9 x 12.2”)
4.3kg (9.5lbs)
Dimensions
85 x 430 x 305mm
(3.0 x 16.9 x 12.2”)
4.3kg (9.5lbs)
Weight
Weight
8
CD 5
CD10
Troubleshooting
There is no power
Ensure the AC power cord is connected securely.
Ensure the plug is fully inserted into the wall socket and is switched on.
Check the unit is switched on at the rear panel.
Check fuse in the mains plug or adaptor.
The player will not read the disc
Check the disc is not loaded upside down.
Check that the disc is not too scratched or dirty.
There is no sound
Ensure that the amplifier is set correctly.
Check that the interconnects are inserted correctly.
The disc is skipping
Check that the disc is not too scratched or dirty.
Ensure the player is on a firm surface and not subject to vibrations.
There is a hum coming from the speaker
Ensure that all cable connections are secure.
The remote handset will not function
Check that the batteries have not expired.
Ensure that nothing is blocking the remote sensor.
In the event that the above solutions do not remedy your problem, please
consult our frequently asked questions (FAQ) section on our website:
You can also use this facility to post a question to our Technical Support
team.
For all servicing, in or out of warranty, please contact your dealer.
9
Cambridge Audio is a brand of Audio Partnership Plc
Registered Office: Gallery Court, Hankey Place,
London, SE1 4BB, United Kingdom
Registered in England No. 2953313
© 2009 Cambridge Audio Ltd
|