Casio Watch 2495 User Manual

USER’S GUIDE 2495  
General Guide  
Press C to change from mode to mode.  
In any mode, press B to illuminate the display.  
Timekeeping Mode  
World Time Mode  
Day Counter Mode  
Telememo Mode  
Stopwatch Mode Countdown Timer  
Mode  
Alarm Mode  
Press  
.
Timekeeping  
Use the Timekeeping Mode to set and view the current time and date.You can  
also select the color of the “Multi Illuminator” backlight, which uses LEDs to  
illuminate the display in different colors.  
In the Timekeeping Mode, press D to toggle the lower part of the display  
between the date and world time.  
To change the backlight color  
1.In the Timekeeping Mode, hold down A until the  
seconds start to flash, which indicates the setting  
screen.  
2.Press C eight times until the backlight color  
setting screen appears, and then use D to cycle  
through the available color settings as shown  
below.  
Hour : Minutes  
Day of week  
Press  
.
AM/PM  
indicator  
Backlight color  
The following shows how the available color settings affects the backlight  
color of the display in each mode.  
Seconds  
Month – Day  
City code type indicator World time  
Color Setting  
Number  
1
2
3
Mode  
Important!  
Timekeeping  
Telememo  
Alarm  
World Time Mode times will not be correct unless you set the correct current  
date and time in the Timekeeping Mode. See “To set the time and date” for  
more information.  
Always use standard time when setting the Timekeeping Mode time and  
date, even if the area where your Home Time city (the city where you  
normally use the watch) is located is currently in Daylight Saving Time  
(summer time). After setting the time, turn DST on or off as required. See  
“Daylight Saving Time (DST)” for more information.  
Tangerine  
Yellow  
Forest  
Green  
Pure Red  
World Time  
Stopwatch  
Tangerine  
Yellow  
Forest  
Green  
Pure Red  
Day Counter  
Countdown Timer  
Forest  
Green  
Tangerine  
Yellow  
Pure Red  
3. Press A to exit the setting screen.  
To set the time and date  
1.In the Timekeeping Mode, hold down A until the  
seconds start to flash, which indicates the setting  
screen.  
World Time  
The World Time shows the current time in 40 cities  
(27 time zones) around the world.  
Hour : Minutes  
City code  
Seconds  
2.Press C to move the flashing in the sequence  
shown below to select other settings.  
The basic time settings of the Timekeeping Mode  
and the World Time Mode are synchronized. The  
Daylight Saving Time (summer time) settings of the  
two modes, however, are independent of each  
other.  
All of the operations in this section are performed in  
the World Time Mode, which you enter by pressing  
C.  
Seconds  
DST on/off  
City code  
Hour  
Month  
Minutes  
Year  
Backlight color  
Day  
Home time  
To view the time in another city code  
In the World Time Mode, press D to scroll city codes  
(time zones).  
3. When the setting you want to change is flashing, use D to change it as  
described below.  
(Hour : Minutes)  
City code type indicator  
For full information on city codes, see the “City  
Code Table” at the back of this manual.  
If the current time shown for a city is wrong, check your Timekeeping Mode  
To change this setting  
Seconds  
Perform this button operation  
00  
Press D to reset to  
.
ON  
displayed)  
DST on/off  
Press D to toggle between DST on (  
time and Home City code settings and make the necessary changes.  
OF  
and off (  
displayed).  
City code  
Use D to scroll through the available codes until the  
one you want to use as your Home Time city is  
displayed.  
To switch between Standard Time and Daylight Saving Time  
In the World Time Mode, hold down A to toggle between Daylight Saving  
Time and Standard Time.  
Hour, Minutes, Year, Month, Day  
Backlight color  
Use D to increase the setting.  
DST indicator  
Use D to cycle through the available color settings.  
Pressing D while the seconds are in the range of 30 to 59 resets them to  
00  
unchanged.  
Hold down  
.
and adds 1 to the minutes. In the range of 00 to 29, the minutes are  
For full information on city codes, see the “City Code Table” at the back of  
this manual.  
See “To change the backlight color” for information about backlight color  
settings.  
4. Press A to exit the setting screen.  
The day of the week is automatically displayed in accordance with the date  
(year, month, and day) settings.  
DST OFF  
DST ON  
The above operation toggles all WorldTime city codes between Daylight Saving  
Time and Standard Time. Note that you cannot make settings for individual city  
codes.  
To toggle between 12-hour and 24-hour timekeeping  
In the Timekeeping mode, hold down D for about two seconds to toggle  
between 12-hour timekeeping and 24-hour timekeeping.  
With the 12-hour format, the P (PM) indicator appears to the left of the hour  
digits for times in the range of noon to 11:59 p.m. and the A (AM) indicator  
appears to the left of the hour digits for times in the range of midnight to  
11:59 a.m.  
With the 24-hour format, times are displayed in the range of 0:00 to 23:59,  
without any indicator.  
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode  
is also applied in all other modes.  
Day Counter  
The Day Counter lets you count the number of days from the Timekeeping  
Mode’s current date to a specific target date.  
Alternates at  
Text area  
the 1-second  
interval  
Number of  
days  
Year Month – Day  
DAYS indicator  
Target date  
Daylight Saving Time (DST)  
Whenever the date specified by any one of the Day Counters matches the  
date of the Timekeeping Mode (regardless of the Day Counter’s year setting),  
the DAYS indicator flashes in the Timekeeping Mode and Day Counter Mode  
screens.  
There are five Day Counter records, each of which can be set with its own  
text and target date (year, month, and day).  
Daylight Saving Time (summer time) advances the time setting by one hour  
from Standard Time. Remember that not all countries or even local areas use  
Daylight Saving Time.  
To toggle the Timekeeping Mode time between DST and Standard Time  
1.In the Timekeeping Mode, hold down A until the  
seconds start to flash, which indicates the setting  
screen.  
DST indicator  
All of the operations in this section are performed in the Day Counter Mode,  
which you enter by pressing C.  
2.Press C to move the flashing to the DST On/Off  
setting.  
3.Press D to toggle between Daylight Saving Time  
ON  
OF  
displayed).  
(
displayed) and standard time (  
4.Press A to exit the setting screen.  
The DST indicator appears on the display when  
Daylight Saving Time is turned on.  
1
 
USER’S GUIDE 2495  
Reference  
To turn auto-repeat on and off  
1.In the Countdown Timer Mode, hold down A until  
the hours of the countdown start time start to flash,  
which indicates the setting screen.  
2.Press B to toggle auto-repeat on (  
and off ( not displayed).  
3.Press A to exit the setting screen.  
This section contains more detailed and technical information about watch  
operation. It also contains important precautions and notes about the various  
features and functions of this watch.  
displayed)  
Auto return features  
If you leave a screen with a flashing setting or a cursor for two or three  
minutes without performing any operation, the watch automatically saves any  
settings you have made up to that point and exits the setting screen.  
If you leave the watch in the Day Counter Mode or Telememo Mode for two  
or three minutes without performing any operation, it automatically changes  
to the Timekeeping Mode.  
When the end of the countdown is reached while  
auto repeat is on, the alarm sounds, but the  
countdown restarts from the beginning without  
stopping. You can stop the countdown by pressing  
D and manually reset to the start time by pressing  
A.  
Auto-repeat indicator  
Data and Setting Scrolling  
The auto-repeat indicator appears in the  
Countdown Timer Mode only.  
The D button is used in various modes and setting screens to scroll through  
data on the display. In most cases, holding down this button during a scroll  
operation scrolls through the data at high speed.  
Alarm  
Initial Screens  
When you enter the World Time, Day Counter or Telememo Mode, the data  
you were viewing when you last exited the mode appears first.  
The alarm sounds at the preset time each day while  
the Daily Alarm is turned on. When the Hourly Time  
Signal is turned on, the watch beeps every hour on  
the hour.  
Alarm indicator  
Hourly time signal  
indicator  
World Time  
You can configure the alarm so it sounds when the  
alarm time setting matches the time either in your  
current Home Time city or the city currently  
selected in the World Time Mode.  
The Hourly Time Signal also sounds in accordance  
with the city you specify in the Alarm Mode.  
If you are planning to specify a World Time city in  
the Alarm Mode, enter the World Time Mode,  
display the city zone you want to use (to select it),  
and then enter the Alarm Mode to set the alarm.  
The current time in all World Time Mode cities is calculated in accordance  
with the Greenwich Mean Time (GMT) differential for each city, based on the  
current Home City time setting in the Timekeeping Mode.  
The GMT differential is the time difference between the time zone where the  
city is located and Greenwich Mean Time.  
GMT differential is calculated by this watch based on Universal Time  
Coordinated (UTC) data.  
Hour : Minutes  
Backlight Precautions  
The backlight uses an LED (light emitting diode) and a light guide panel that  
cause the entire display to glow for easy reading in the dark. In any mode,  
press B to illuminate the display for about three seconds.  
If the DST indicator is on the display in the Alarm Mode, it means that Daylight  
Saving Time (summer time) is turned on for the city that is specified in the  
Alarm Mode.  
Alarm setting (and Hourly Time Signal setting) is available in the Alarm Mode,  
which you enter by pressing C.  
The illumination provided by the backlight may be hard to see when viewed  
under direct sunlight.  
The backlight automatically turns off whenever an alarm sounds.  
Frequent use of the backlight shortens the battery life.  
To set the alarm time  
1.In the Alarm Mode, hold down A until the city  
Alarm on indicator  
City code  
code flashes on the display, which indicates the  
setting screen.  
At this time, the alarm is turned on automatically.  
2.Press C  
below.  
to move the flashing in the sequence shown  
City code  
Hour  
Minutes  
3.While the city code is flashing, press D to toggle  
between your Home Time city (which you selected  
in the Timekeeping Mode) and the city that is  
currently selected in the World Time Mode.  
The city code type indicator ( ) shows whether  
the alarm setting is based on your Home Time  
city (HOME) or aWorldTime Mode city (WORLD).  
City code type indicator  
4. While the hour or minute setting of the alarm time is flashing, press D to  
increase it.  
5. Press A to exit the setting screen.  
When setting the alarm time using the 12-hour format, take care to set the  
time correctly as morning (A displayed) or afternoon (P displayed).  
Changing the city code for the time (Home City time or World Time Mode  
time) also causes the Alarm Mode city code to change.  
Alarm Operation  
The alarm tone sounds at the preset time for about 20 seconds.  
Pressing any button stops the alarm tone.  
To test the alarm  
In the Alarm Mode, hold down D to sound the alarm.  
Note that pressing D to test the alarm also cycles through the Daily Alarm  
and Hourly Time Signal settings described below.  
To turn the Daily Alarm and Hourly Time Signal on and off  
In the Alarm Mode, press D to cycle through the Daily Alarm and Hourly Time  
Signal settings shown below.  
Alarm On Indicator / Hourly Time Signal On Indicator  
Both ON  
Both OFF  
Daily Alarm  
only  
Hourly Time  
Signal only  
3
 

Black Decker Sander BDSA100 User Manual
Blue Rhino Outdoor Fireplace WAF741SP User Manual
Boston Acoustics Speaker System RK6T2 User Manual
Briggs Stratton Pressure Washer 20320 User Manual
Brother Sewing Machine 885 V60 User Manual
Cambridge SoundWorks Clock Radio I525 User Manual
Casio Digital Camera EX Z400 User Manual
Century Elliptical Trainer PM 1722AC User Manual
CFM Fan WEB 0807 User Manual
Chicago Electric Battery Charger 90636 User Manual