Model 973-315LM Security✚®
3-Button Remote Control
OWNER’S MANUAL
The 900 Series remote control works only with door openers and
light controls having an orange “Learn” button.
WARNING
To prevent possible SERIOUS INJURY or DEATH from a moving gate
Programming instructions are described and illustrated below.
The additional push buttons can also activate other garage door
openers and/or light controls. (Instructions for programming light
products are included with those accessories.)
or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER
permit children to operate, or play with remote control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
Instructions are Described and Illustrated Below
If you have a lighted push button that looks like the lighted
push button illustrated follow the instructions below.
1. Remove the cover from the Lighted Door
Control.
To Erase All Codes From Motor Unit Memory
2. Press and hold the button on the
hand-held remote that you wish to operate
your garage door.
To deactivate any unwanted remote, first erase all codes:
Press and hold the “learn” button on motor unit
until the learn indicator light goes out
(approximately 6 seconds). All previous codes
are now erased. Reprogram each remote or
keyless entry you wish to use.
3. While holding the remote button, press
and hold the “A” button on the Lighted
Door Control.
"A"
Button
The Remote Control Batteries
4. Continue holding both buttons while you
press the “B” button on the Lighted Door
Control (all three buttons are held).
"B"
Button
WARNING
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
5. Release buttons when the motor unit
lights blink. It has learned the code. If light
bulbs are not installed, two clicks will be
heard.
• If battery is swallowed, immediately notify doctor.
The lithium batteries should produce
power for up to 5 years. To replace,
pry open case with visor clip or
screwdriver, as shown. Insert
batteries positive side up (+).
If you have a multi-function wall control follow instructions
below.
Battery
positive
side up (+)
1. Press and hold the button on the
hand-held remote that you wish to
operate your garage door.
Dispose of old batteries properly.
2. While holding the remote button, press
and hold the light button on the
Multi-Function Door Control.
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
LOCK
LIGHT
3. Continue holding both buttons while you
press the push bar on the Multi-Function
Door Control (all three buttons are held).
LOCK
LIGHT
Replacement Parts
3V2032 Lithium battery . . . . . . . . . . . . . . . . . . . . . . . . . .10A20
Visor clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29B137
4. Release buttons when the motor unit
lights blink. It has learned the code. If light
bulbs are not installed, two clicks will be
heard.
If neither of the two programming instructions match your
type and style of opener follow instructions below.
Press and release the “learn” button on the motor unit. The learn
indicator light will glow steadily for 30 seconds. Within 30
seconds, press and hold the button on the hand-held remote.
Release the button when the motor unit light blinks. It has learned
the code. If light bulbs are not installed, two clicks will be heard.
© 2006, Chamberlain Group Inc.
All Rights Reserved
114A2572D
|